Trilithic 180 DSP Скачать руководство пользователя | Manualshive

Страница: 31 / 386

background image

www.trilithic.com

Page I-12

180 DSP Operation Manual

Signal Level Meter

Standard Interfaces

• One or Two RF Test Ports (F-Type), dependent on RF board*

• The 1 GHz RF board has 1 RF Test Port
• The 1.25 GHz RF board has 2 RF Test Ports

• RJ45 Management Port (10/100 Mbps)
• USB 2.0 Flash Drive Port

Standard Testing Features

•  Level Measurement
•  C/N Measurement
•  QAM Measurement (MER/BER/Constellation/EQ)
•  Complete Channel Plan Scan with Tilt Measurement
•  Return Spectrum Analysis (4 to 110 MHz)
•  Ping, TraceRoute, VoIP & Throughput Measurements

Optional Features

The following optional features are available for the 180 DSP.

Analog & Digital HUM Measurement

This feature enables the 180 DSP to measure the amplitude of the 50/60 Hz, 100/120

Hz, and low frequency interference (HUM) present on the video/QAM carrier of a single

selected analog or digital channel.

Forward Spectrum Analysis

This feature enables the 180 DSP to view raw forward spectrum traces from 5 to 1000

MHz (units equipped with 1 GHz RF board) or 5 to 1250 MHz (units equipped with

1.2 GHz RF board) with DSP spectrum snapshots to give the user your downstream

channels.

«
...
29
30
31
32
33
...
»

Содержание 180 DSP



































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 180 DSP

Бренд: Keithley Страницы: 48

Бренд: R.M. Young Страницы: 2

Бренд: Ebtron Страницы: 5

Бренд: Okolab Страницы: 4

Бренд: Fly Henry Страницы: 5

Бренд: CAS Corporation Страницы: 20

Бренд: JensPrima Страницы: 20

SoundExpert LxT

Бренд: Larson Davis Страницы: 307

Panel Scope VPS10

Бренд: Velleman Страницы: 60

Бренд: Gatekeeper Страницы: 2

Бренд: Midtronics Страницы: 58

Бренд: PHYWE Страницы: 6

Бренд: QUNDIS Страницы: 6

Бренд: wattwatchers Страницы: 2

Бренд: a&p instruments Страницы: 20

InnovaSonic 205i

Бренд: Sierra Страницы: 12

Бренд: Prexiso Страницы: 10

Бренд: Delphin Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды