Trilithic 180 DSP Скачать руководство пользователя страница 133

Страница: 133 / 386

www.trilithic.com

Page II-68

180 DSP Operation Manual

Signal Level Meter

Editing Limit(s)

To edit limit(s) within the limit set, use the

up/down arrow buttons to highlight the

limit(s) to be edited and select the

Enter

button.
The

Edit Limit

screen will be displayed as

shown to the right. Use the left/right arrow

buttons to highlight the threshold that you

would like to change.
Use the up/down arrow buttons or select

the

Enter

button and use the

Virtual

Keyboard

to enter the threshold.

Содержание 180 DSP



































































































































































































































































































































































































Результаты поиска

Содержание 180 DSP

Отзывы:

Бренды по названию

Популярные бренды

Trilithic 180 DSP, Руководство по эксплуатации

Результаты поиска

Содержание 180 DSP

Отзывы:

Бренды по названию

Популярные бренды