Tridonic ADV3 OTD Скачать руководство пользователя

Страница: 5 / 63

Manual LCO EXC3/ADV3 OTD | 03-2020 | 1.2 | en

General safety instructions

5 / 63

The instructions in this section have been compiled to ensure that operators and users of LED Drivers of the LCO NFC C EXC3 and

series from Tridonic are able to detect potential risks on time and take the necessary preventative measures.

LCO NFC C ADV3
The operator must ensure that all users fully understand these instructions and follow them. This device may only be installed and
configured by suitably qualified personnel.

Intended use

Proper use

Operation of LED light modules. The device may only be used for this intended purpose.

Improper use

Outdoor use. Extensions and modifications to the product.

Dangers associated with the operation of the system

Environment

WARNING!

Improper use could result in injury, malfunction or damage to property.
It must be ensured that the operator informs every user of existing hazards.

DANGER!

Danger of electrocution
Disconnect the power of the entire lighting system before working on the lighting system!

DANGER!

Not to be used in corrosive or explosive environments.

CAUTION!

Risk of damage caused by humidity and condensation

Use use the control device only in dry rooms and protect it against humidity!

Prior to commissioning the system, wait until the control device is at room temperature and completely dry!

Содержание ADV3 OTD
































































Результаты поиска

Содержание ADV3 OTD

Отзывы:

Похожие инструкции для ADV3 OTD

Бренды по названию

Популярные бренды

Tridonic ADV3 OTD, Руководство по эксплуатации продукта

Результаты поиска

Содержание ADV3 OTD

Отзывы:

Похожие инструкции для ADV3 OTD

Бренды по названию

Популярные бренды