Triax CG2CT 860 C Скачать руководство пользователя

Страница: 31 / 36

- 31 -

CG2CT 860 C

et work

nfor m ation

able

(nit)

Bx 2
off

NIT

=> Make

• To switch NIT "

" resp. "

off

" press the

buttons.

• Press the button to activate NIT ("

Make

").

All active modules which are able to output a NIT ("NIT modules") must be

set and ready for reception.

—> The NIT of all

NIT modules

are switched on.

—> The module fetches all the information (output frequencies, output

data rates, etc.) it needs from all the "NIT modules" in order to gen-
erate the NIT. This process may take a few seconds.

Then the NIT is generated, added and sent to all "NIT modules". The
other "NIT modules" also add this new NIT. The status of all "NIT
modules" in the NIT menu changes to "

The display shows: "

read … / copy …

• To switch off the new NIT ("

off

") press the button.

—>

The NITs of the other "NIT modules" will stay switched on. When

the NIT of the module is switched on again ("

") by pressing the

button, the previously generated NIT is added again. If you have

changed parameters in the meantime, you must first select "

Make

" to

generate a new, up-to-date NIT.

• Press the button.

—> The "Factory reset" – "

FACTORY Defaults

" main menu is activated.

Содержание CG2CT 860 C





































Результаты поиска

Содержание CG2CT 860 C

Отзывы:

Похожие инструкции для CG2CT 860 C

Бренды по названию

Популярные бренды

Triax CG2CT 860 C, Руководство по сборке

Результаты поиска

Содержание CG2CT 860 C

Отзывы:

Похожие инструкции для CG2CT 860 C

Бренды по названию

Популярные бренды