TRIAD DISTRIBUTED AUDIO SERIES IN-CEILING SPEAKERS - QUICK START GUIDE
NEW CONSTRUCTION INSTALLATION
Locate the area where the speaker will be placed in the wall or ceiling, keeping in
mind that when the speaker is installed, it may take up the full wall cavity within
the NCB location (keep free from electrical wires, HVAC, and plumbing). Position
the bracket between the two joists or studs so the flange protrudes out for
drywallers to sheetrock around.
NCB: IC5, IC6, IW8
Attach New Construction Bracket (NCB) wings before use.
Fasten each NCB wing to the stud/joist with two screws, nails, or staples
through each wing.
RETROFIT INSTALLATION
Determine the location that you would like to mount the speaker.
Important!
Verify that there are no other obstructions (such as conduit,
pipes, HVAC ducts, or pocket doors) behind the area where you would
like to install the speaker. You may need to drill a small hole in the
center of your selected area and insert a wire hangar into the hole to
"feel" around for any possible obstructions.
Tip:
Use a stud finder to locate the two studs or joists flanking the
location where you want to install the speaker.
Important!
Avoid putting a speaker right up against a stud/joist, as the
mounting legs need a little space to engage. Keep the hole cutout a
minimum of 1" (25 mm) from the edge of the nearest stud.
Once you have confirmed the location, proceed with the following steps:
Using the enclosed hole cutout template as a guide, mark the outline on the
wall or ceiling with pencil.
Slowly cut along the outlined mark with a drywall knife/saw, trying not to
chip out the drywall excessively.
MESSAGE FROM TRIAD
Thank you for purchasing a Triad Distributed Audio Series (DA Series) loudspeaker.
We designed and engineered each loudspeaker with pride in the United States of
America with the utmost attention to quality, décor-friendly design, and
high-performance sound—eliminating costly frills and features that add nothing to
sound quality.
We trust that you will hear the benefits of this engineering each time you play
them.
Thanks again and happy listening.
Triad Audio
1
2
3
1
2
3
INSTALLATION NOTES / CAUTIONS
For all non-sealed ("open back") speakers:
Caution!
Operating a speaker beyond its maximum power rating may result in the
speaker overheating and/or failure, In addition, always maintain the following
minimum clearances:
Non-flammable materials
Flammable materials
1" (26 mm)
3" (78 mm)
Caution!
Do not over-tighten the mounting dogleg clamps.
Over-tightening the mounting dogleg clamps on any Triad speaker may result in
damage to the speaker mounting hardware, damage to the ceiling/wall, and/or
deflection of the speaker frame during installation.
Should you notice any of the above during installation, loosen the mounting dog
leg clamps so the speaker frame is flat with the mounting surface. This will help
ensure that the grill contacts the mounting surface all the way around the
speaker for a proper fit.
If using a power screwdriver or drill to install this product, ensure that the clutch
is set to its lowest setting to avoid over-tightening.
Important!
The Distributed Audio Series speakers are designed to be mounted
into drywall/plasterboard or suspended ceilings/walls with a surface thickness
between:
MORE INFORMATION
For complete specs on Triad Distributed Audio Series speakers,
visit the Triad Portal, view the Products sections at
www.triadspeakers.com, or scan the QR code shown here:
If these speakers are being installed during new home construction, using Triad's New
Construction Brackets (NCB) can simplify the process. These brackets make finish
installation easier by reserving the exact space and size needed for the speaker during
the framing stage of home construction. During the drywall process, the cutout can
be precisely made around the bracket flange.
To use the new construction bracket:
Pull speaker cable from the NCB to the amplifier location.
Consult local building codes before running speaker wires inside walls
for a full understanding of any special regulations/requirements.
4
Pull pre-wired speaker cable through the cutout or run the speaker
wire from the cutout to the amplifier location.
Consult local building codes before running speaker wires inside walls
for a full understanding of any special regulations/requirements.
4
In-ceiling models
In-ceiling shallow-depth models
3/8" - 1 1/8" (10 - 28 mm)
1/8" - 3/4" (3 - 19 mm)
