background image

10

Two 22KHz tone generators are supplied in the 
kitpack. Install these devices in-line with the 
antenna’s RF cables as explained below. 

If a 

multiswitch is installed, skip to page 11.

a.

Disconnect the RF1 cable from the primary 

receiver’s “Satellite In” connector.

b.

Connect the RF1 cable to the 22KHz tone 

generator’s “LNB” connector.

c.

Connect a supplied RG-179 RF cable from the 

22KHz tone generator’s “REC” connector to 

the primary receiver’s “Satellite In” 

connector.

d.

If you have a second receiver installed, repeat 

steps a-c to install the second 22KHz tone 

generator between the secondary receiver 

and the RF2 cable.

e.

Set the 22KHz tone generator’s “22KHz OFF/

ON” switch to the proper position for the 

satellite TV service you wish to receive:

OFF

 = DIRECTV, DISH Network, ExpressVu

ON

 = DIRECTV Latin America (Galaxy)

If you have two receivers installed, set the switch 

on both 22KHz tone generators.

f.

Reconnect power to the TracVision system 

components.

g.

Turn on the TracVision antenna and 

configure it to track satellites that are 

compatible with the Tri-Americas LNB. 

These include DIRECTV, DISH Network 

(EchoStar), ExpressVu, or Galaxy. 

Refer to the 

TracVision M5/M7 User’s Guide for details.

Antenn

a

S

econd

a

ry Receiver - Option

a

l

Prim

a

ry Receiver

Thi

s

 receiver control

s

 

sa

tellite 

s

election

RF1

RF2

(Option

a

l)

RF1

RF2

(Option

a

l)

22KHz Tone Gener

a

tor

S

et 

s

witch “ON” for G

a

l

a

xy

22KHz Tone Gener

a

tor

S

et 

s

witch “ON” for G

a

l

a

xy

Gro

u

nding Block

(If In

s

t

a

lled)

Sa

tellite In

Sa

tellite In

LNB

REC

LNB

REC

Figure 20:  Tone Generator Wiring

Installing the Tone Generators

One or Two Receivers

Содержание TracVision M7











Отзывы: