background image

2021 E-Caliber Service Manual

17

Carriage wiper seals and bushings (continued)

Replace the wiper seals

1. 

Wipe the seal surface inside the carriage to remove 

debris.

2.  Load a new seal onto each seal installation tool.

Seal

 

Use this side of the tool for pressing in 

seals.

 

 

Bushing

 

Use this side of the tool for pressing in 

bushings.

3. 

Put one tool with one seal into the front of the car-

riage, and the other tool with the other seal into the 

rear of the carriage.

4. 

Insert the upper half of the headset press into the 

front of the carriage.

5. 

Insert the lower half of the headset press into the 

rear end of the carriage and lock it into place.

6. 

Spin the headset press until it is snug against the 

seal tool.  Check for the correct alignment of the 

press, tools and seals. Rotate the press to push the 

seals into place.

7.  Tighten the press until you feel resistance. Once you 

feel resistance, remove the press and tools.

8. 

Inspect the seals to verify that there is no gap be-

tween the seal and the carriage.

9.  Soak the foam ring in 10 wt fork bath oil.
10.  Install the foam ring into the front of the carriage.

Содержание 2021 E-CALIBER























Отзывы: