Travis Industries 94500982 Скачать руководство пользователя страница 1

 

4237 EG - Oak & Birch Log Set 

(Birch - sku# 94500982) (Oak - sku# 94500983).

 

 

Page 1 of 10 

17602208 —9/15/2021 

© Travis Industries, Inc.  

Compatibility 

  4327 EG Fireplaces 

Packing List 

  9 Piece Log Set

 

Installation Warnings 

NOTE

:  Consult the installation manual for order of installation.  If using propane (LP), convert the appliance 

before installing the log set.  If using firebacks, install them prior to installing the log set. 

 

WARNING

 

 

  The logs are fragile, especially after being exposed to heat. 

  Make sure the gas control valve is OFF and the heater is cool prior to conducting service. 

  Failure to position the parts in accordance with these diagrams or failure to use only parts specifically 

approved with this appliance may result in property damage or personal injury. 

  The burner must be correctly positioned before installing the log set. Make sure the burner is fully seated and 

the pilot is properly aligned. See owner’s manual for details on burner removal.

 

Installation – Oak vs. Birch 

Both log sets are nearly identical in shape.  The only difference is the paint scheme and some textural details.  
Below you will find pictures of both the birch and the oak log sets.  The installation pictures show the oak log 
set. 

Log Set Overview - Oak (sku# 94500983) 

When installed, the nine (9) logs should appear as shown below.   
 

 

 

 

Log #1 

250-05840 

Log #2 

250-05841 

Log #8 

250-05847 

Log #6 

250-05845 

Log #5 

250-05844 

Log #9 

250-05848 

Log #4 

250-05843 

Log #3 

250-05842 

Log #7 

250-05846 

Содержание 94500982











Отзывы: