Transmitter Solutions TS-NX/CL Скачать руководство пользователя страница 10

Страница: 10 / 54

TS-‐NX/CL

INSTALLATION MANUAL

Page 9

4 START UP

VERY

IMPORTANT

USE A TYPICAL SIM CARD (mini-SIM, see the picture



)

WITH MEMORY FOR UP TO 250 CONTACTS!

⇒

Insert SIM card to be used for TS-NX/CL in your personal mobile phone.

IMPORTANT

ERASE THE PIN CODE!

⇒

Insert SIM card in TS-NX/CL device. The unit must be switched OFF when

you insert the SIM!

⇒

Connect inputs and outputs to TS-NX/CL.

⇒

Connect the antenna to antenna connector.

⇒

Connect power cable to TS-NX/CL device

⇒

Connect device to source power supply voltage.

⇒

Wait until LED3 display is turned ON (green) and LED1 (blue) starts flashing.

This is set in around 1 minute.

⇒

TS-NX/CL unit is now ready to operate.

IMPORTANT

Before sending any SMS commands to TS-NX/CL device, TS-
NX/CL must be in normal operation!

NOTE

TS-NX/CL device will “beep” in 15s interval until the device is not in
normal operation.

Содержание TS-NX/CL























































Результаты поиска

Содержание TS-NX/CL

Отзывы:

Похожие инструкции для TS-NX/CL

Бренды по названию

Популярные бренды

Transmitter Solutions TS-NX/CL, Руководство по установке

Результаты поиска

Содержание TS-NX/CL

Отзывы:

Похожие инструкции для TS-NX/CL

Бренды по названию

Популярные бренды