4
CMEFG10xx-1xx / SMEFG10xx-1xx
24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Stand-Alone Media Converter
•
Copper to Fiber
•
10/100/1000Base-TX to 1000Base-SX/LX
•
Small Form Fact Pluggable (SFP) Fiber Port
Transition Networks SMEFG1040-1xx series media
converters connect 10Base-TX, 100Base-TX, or
1000Base-TX twisted-pair copper cable to 1000Base-
SX or 1000Base-LX fiber cable.
The SMEFG1040-10x has one copper port and one
SFP port.
SMEFG1040-1xx
*Typical maximum cable distance. Actual distance is dependent upon the physical
characteristics of the network.
Note:
Third-party Multi-Source Agreement (MSA) compliant Small Form Factor
Pluggables (SFPs) can also be used in the SFMFF1040-1xx device.
The following DMI supported SFP transceiver modules are compatible with the
SFMFF1040-1xx converter and are available from Transition Networks
(sold separately)
.
Part Number
Duplex Fiber-Optic Port 2
TN-SFP-SX
LC, 1000Base-SX, 850 nm multimode, 220-550 mm
(720-1804 ft)
*
TN-SFP-LX1
LC, 1000Base-LX, 1310 nm single mode, 10 km
(6.2 miles)
*
TN-SFP-LX3
LC, 1000Base-LX, 1310 nm single mode, 30 km
(18.8 miles)
*
TN-SFP-LX5
LC, 1000Base-LX, 1550 nm single mode, 50 km
(31.2 miles)
*
TN-SFP-LX8
LC, 1000Base-LX, 1550 nm single mode, 80 km
(50.0 miles)
*
Copper Port 1:
10/100/1000-Base-TX
RJ-45 100 m
(328 ft)
CMEFG1040-1xx
Slide-in-Module Media Converter
•
Copper to Fiber
•
10/100/1000Base-TX to 1000Base-SX/LX
•
Small Form Fact Pluggable (SFP) Fiber Port
Transition Networks CMEFG1040-1xx series media
converters, designed to be installed in a PointSystem™
chassis connect 10Base-TX, 100Base-TX, or 1000Base-
TX twisted-pair copper cable to 1000Base-SX or
1000Base-LX fiber cable. It has one copper port and
one SFP port.
Part Numbers
CMEFG1040-1xx and SMEFG1040-1xx
[email protected] -- Click the “Transition Now” link for a live Web chat.
5
Installation
Install the CMEFG10xx-10x
CAUTION: Wear a grounding device and observe electrostatic discharge
precautions when installing the CMEFG10xx-1xx media converter in the
PointSystem™ chassis. Failure to observe this caution could result in damage to,
and subsequent failure of the CMEFG10xx-1xx media converter.
To install the CMEFG10xx-1xx media converter slide-in-module:
1.
Locate an empty installation slot on the
PointSystem™
chassis.
2.
Carefully insert the slide-in-module into the slot, aligning the module with the
slot guides.
3.
Ensure that the module is firmly seated against the back of the chassis.
4.
Push in and rotate the panel-fastener screw
Media Converter
Point System Chassis
Panel Fastener
Slot
Note:
The CMEFG10xx.1xx is not designed for use in the Transition Networks
single-slot chassis. It will work in all other Transition Networks chassis.
