Transition Networks S4224 Скачать руководство пользователя страница 293

Страница: 293 / 669

Transition Networks

S4224 Web User Guide

33558 Rev. C

https://www.transition.com

Page 293 of 669

Configuration > Ethernet Services > EVCs

The

Configuration

Ethernet

Services

EVCs

menu path displays current EVC configurations. The

EVC settings can also be configured here. On this system, only Provider Bridge based EVCs are

supported.

Figure 8. Provider Bridge E-LINE Service

The EVC (Ethernet Virtual Connection) is an association of two or more UNIs that limits the exchange of

frames to UNIs in the Ethernet Virtual Connection. The User Network Interface (UNI) is the physical

interface or port that is the demarcation between the customer and the service provider/Cable

Operator/Carrier/MSO. The UNI is the physical demarcation point between the responsibility of the

Service Provider and the responsibility of the Subscriber.

MEF Ethernet Virtual Connection Types

The Metro Ethernet Forum (MEF) specifies these EVC (Ethernet Virtual Connection) types:

E-Line

EVC: Point-to-point Service Ethernet Private Line (EPL) allows only one EVC per UNI port, while

Ethernet Virtual Private Line (EVPL) allows multiple EVCs per UNI port. The figure below shows a

Provider Bridge E-LINE service example.

Figure 9. Provider Bridge E-LINE Service

E-LAN

EVC: Multipoint Service Ethernet Private LAN (EP-LAN) allows only one EVC per UNI port, while

Ethernet Virtual Private LAN (EVP-LAN) allows multiple EVCs per UNI port. This is a bridged service.

E-TREE

EVC: Rooted Multipoint Service Ethernet Private Tree (EP-TREE) allows only one EVC per UNI

port, while Ethernet Virtual Private Tree (EVP-TREE) allows multiple EVCs per UNI port. This is a bridged

service where the root port has access to all the leaf ports, but the leaf ports only have access to the root

port.

Содержание S4224






























































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание S4224

Отзывы:

Похожие инструкции для S4224

Бренды по названию

Популярные бренды

Transition Networks S4224, Руководство пользователя для веб

Результаты поиска

Содержание S4224

Отзывы:

Похожие инструкции для S4224

Бренды по названию

Популярные бренды