Transition Networks S4224 Скачать руководство пользователя страница 278

Страница: 278 / 669

Transition Networks

S4224 Web User Guide

33558 Rev. C

https://www.transition.com

Page 278 of 669

Port Isolation

You can configure port isolation from the

Configuration

Private VLANs

Port Isolation

menu path.

This page is used for enabling or disabling port isolation on ports in a Private VLAN. Port isolation offers

isolation of that Port from the VLAN forwarding on the VLAN that it is a member of.

A port member of a VLAN can be isolated to other isolated ports on the same VLAN and Private VLAN.

Port Members

A checkbox is provided for each port of a private VLAN.

When checked, port isolation is enabled on that port, and that port is considered “isolated”.

Isolated ports configured as part of a PVLAN cannot communicate with each other.



When unchecked, port isolation is disabled on that port, and that port is considered a “member

port”. Member ports of a PVLAN are not isolated and can communicate with each other.

By default, port isolation is disabled (unchecked) on all ports (i.e., all ports are “member ports” at

default).

Note

: At least one port entry must be selected in order to add a new entry.

Buttons

Auto-refresh

: Check this box to refresh the page automatically every 3 seconds.

Refresh

: Click to refresh the page immediately.

Save

: Click to save changes.

Reset

: Click to undo any changes made locally and revert to previously saved values.

Содержание S4224






























































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание S4224

Отзывы:

Transition Networks S4224, Руководство пользователя для веб, Страница: 278 / 669

Результаты поиска

Содержание S4224

Отзывы: