background image

 

 

NM2-FXS-2230-SFP-01 Install Guide 

33730 Rev. C 

           

https://www.transition.com

  

Page 

8

 of 

14

 

Pre-Installation Checklist  

Before installing your NIC, review the preceding sections, and then do the following:  
1. Verify that your system is using the latest BIOS.  
2. If you download the driver software, record the path where you saved the downloads.  
3. If your system is active, shut it down. Do not install the NIC until system power is completely removed. When system 
shutdown is complete, power OFF and unplug your system.  
4. Holding the NIC by the edges, remove it from its shipping package and place it on an antistatic surface.  
5. Check the NIC for signs of damage, particularly on the PCB edge connector. CAUTION: Never attempt to install a 
damaged NIC card. If the NIC is damaged, report it to Transition Networks.  
6. CAUTION: Wear a grounding device and observe electrostatic discharge precautions when installing the NIC in a 
system. Failure to observe this caution could result in damage to the NIC. Before installing the NIC, ensure that system 
power is OFF, the power cord is unplugged from the power outlet, and that proper electrical grounding procedures have 
been followed.  
7. CAUTION: Install the NIC in an operating environment where the temperature range is from 0°C to +45°C (+32°F to 
+113 °F), with relative humidity of 5% to 90% non-condensing. Failure to observe this caution could result in poor 
equipment performance.  
8. CAUTION: DO NOT install the NIC in areas where strong electromagnetic fields (EMF) exist. Failure to observe this 
caution could result in poor equipment performance and data corruption.  

 

NM2-FXS-2230-SFP-01

  

9. Note: You must install the TN-SFP-GE-100FX in the open SFP slot before you power up the PC. 

10. Class I Laser Compliance: This product has been tested and found to comply with the limits for FDA Class I laser for 
IEC60825, EN60825, and 21CFR1040 specifications.

 

Warning: Visible and invisible laser radiation when open. DO NOT 

stare into laser beam or view directly with optical instruments. Failure to observe this warning could result in damage to 
your eyes or blindness. 

 
 
 

 

 

Содержание NM2-FXS-01















Отзывы: