Transmit
On
SQE
E-FRL-MC01
RX
TX
Off
Link
Receive
Power
Collision
Ethernet™
10Base FL Transceiver
Jabber
The TRANSITION Networks Fiber Optic Micro-ceiver (E-FRL-MC01(C)) is a compact
unit used in an Ethernet IEEE 802.3 type of network. It can be connected directly to any
Ethernet workstation, hub or AUI (Attachment Unit Interface) attachment cable.
The Micro-ceiver has an AUI (DB-15) port interface on one end and two ST type fiber
connections on the other. NOTE: An SMA type fiber connection is also available on
the Micro-ceiver E-FRL-MC01C(SMA).
Fiber Optic 10BaseFL Ethernet
Micro-ceiver™ (Transceiver)
E-FRL-MC01(C)
USER’S GUIDE
FCC Regulations:
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at his own cost.
NOTE:
This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out
on the radio interference regulations of the Canadian Department of Communications.
NOTE:
This equipment has been tested and found to comply with VDE Class B requirements.
For selling in the Federal Republic of Germany:
Hiermit wird bescheinigt, das der E-FRL-MC01 oder E-FRL-MC01(SMA) in Ubereinstimmung mit den
Bestimmungen der Vfg. 243/1991 funk-entstoert ist. Der Deutschen Bundespost wurde das
Inverkehgringen dieses Geraetes angezeigt und die Berechtigung zur Ueberpruefung der Serie auf
Einhaltung der Bestimmungen eingeraumt. TRANSITION Networks, Inc.
Canadian Regulations:
Note: This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out on the
radio interference regulations of the Canadian Department of Communications.
Copyright Restrictions
© 1995 Transition Networks, Inc.
All rights reserved. No part of this work may be reproduced or used in any form or by any means - graphic,
electronic, or mechanical - without written permission from Transition Networks, Inc.
Trademarks:
Ethernet is a registered trademark of the Xerox Corporation, Inc.
ST is a trademark of AT&T.
TRANSITION Networks and Micro-Ceiver are trademarks of TRANSITION Networks Inc
7314 F
Specifications:
Case size dimensions:
3.5" x 1.75" x 0.8"
(89 mm x 44 mm x 20 mm)
Fiber Connection:
ST type connectors (SMA type available upon
request)
Fiber Optic Cable Maximum Distance: 2,000 meters (6,600 feet)
Fiber Optic Cable Recommended:
62.5 / 125 µm multimode fiber
Optional:
100 / 140 µm multimode fiber
85 / 125 µm multimode fiber
50 / 125 µm multimode fiber
Fiber Optic Transmitter Power:
Average power:
-15.0 dBm
Peak power:
-12.0 dBm ±1dBm
Fiber Optic Receiver Power:
Average power:
-32 dBm
Bit error rate:
≤
10-
10
AUI Port:
DB-15 with locking posts.
AUI Maximum Distance:
50 meters (165 feet)
Mean Time Between Failure:
264,410 hours
Environment:
0–50 degrees C,
10–90% humidity, non-condensing,
0–10,000 foot altitude
Warranty:
Five years
Minneapolis, MN 55344 USA
Status LEDs provide the following information:
Transmit:
Flashing or illuminated green LED indicates packet(s) are being transmitted.
Receive:
Flashing or illuminated green LED indicates packet(s) are being received.
Link:
Illuminated green LED indicates the unit is receiving link pulses from a
compliant device.
Power:
Illuminated green LED indicates power to the E-FRL-MC01(C).
Collision:
Flashing or illuminated red LED indicates collisions are occurring.
Jabber:
Illuminated red LED indicates Jabber on the line.
