background image

Ethernet™ 2-Port

6

13

Multi Media Repeater

Male AUI Connector/PC Connection

The male AUI card (E-AUI-DC-SIC) provides a male AUI connector for
connection, through an AUI drop cable, to a 10Base5 port on a
powered PC.

Fiber Optic Connector/10BaseFL Connection

The fiber optic card (E-FRL-SIC) provides one set of transmit (TX) and
receive (RX) ST connectors to fiber optic cable.
The redundant fiber optic card (E-FL/RED-SIC) provides a back-up fiber
optic connection by using two sets of transmit (TX) and receive (RX) ST
connectors to fiber optic cable.

Ensuring Correct 10BaseT Configuration

The 10BaseT cable and RJ-45 jacks for Hub to Terminal connections
must be configured as straight through. The 10BaseT cable and RJ-45
jacks for Hub to Hub connections must be configured as crossover.

The two active pairs  in a 10BaseT network are pins 1 & 2 and pins 3
& 6. Use only dedicated wire pairs (such as blue/white & white/blue,
orange/white & white/orange) for the active pins.

Straight Through Cable

at RJ-45 Plug

Hub . . . . . . . . . . . . . . . .PC, transceiver, NIC, printer

RJ-45 Male   . . . . . . . . . . . . . . .RJ-45 Male

1  . . . . . . . . . . . . . . . . . . .1
2   . . . . . . . . . . . . . . . . . .2
3   . . . . . . . . . . . . . . . . . .3
6  . . . . . . . . . . . . . . . . . . .6

1

8

RJ-45

 

P

LUG

1

8

2 3 4 5 6 7

RJ-45

 

J

ACK

up to 2000 meters

Crossover Cable 

at RJ-45 Plug

Hub   . . . . . . . . . . . . . . .Hub

RJ-45 Male   . . . . . . . . . . . . . . .RJ-45 Male

1  . . . . . . . . . . . . . . . . . . .3
2  . . . . . . . . . . . . . . . . . . .6
3   . . . . . . . . . . . . . . . . . .1
6   . . . . . . . . . . . . . . . . . .2

Содержание E-MMR-2













Отзывы: