TransCore MPRX 10-7200-001 Скачать руководство пользователя страница 69

Страница: 69 / 138

Software Flow Control disabled

Software flow control enabled (factory default)

start of message character is #
For example, if factory default settings are assigned, the reader message is:

ECPS P0 TFE X1 S0

which means basic protocol selected, an ECP timeout of 254 (12,700 ms or 12.7 sec),

software flow control enabled, and start of message character is

527 Display RF Status

527

displays the current status of the RF module. The reader response indicates whether

RF is controlled externally by the host, set by Command

#640N

RF Control, or

internally by input set by Command

#641

(not applicable to the MPRX). RF always is

controlled by Sense 0 and Sense 1 when reader is in MPRX mode. Sense 0 enables RF

on antenna ports 0 and 1, and Sense 1 enables RF on antenna ports 2 and 3. Refer to

“MUX Operational Modes” on page 5–85

. Command

#527

also displays the current

RF status and the uniqueness timeout.

Note:

If you enter RF settings using Command

#642NN

, the display command for RF output

frequency, F is

“Fxx”

and indicates use of the backward-compatible frequency entry method.

Reader response:

RFST C<0 to 1> O<0 to 1> T<1 to 3> Fxxx Rxx Gxx Axx Ixx

where

RF controlled by host

RF controlled by presence sensor on input 0, the red/green pair (factory default

)

RF off

RF on

Uniqueness timeout of two minutes

Uniqueness timeout of 15 seconds

Uniqueness timeout of 30 seconds

Fxxx

RF output frequency, xxx = 000 to 118 hexadecimal offset in 250 kHz from 860 MHz. If

an invalid frequency value is stored (corrupted NVRAM), then xxx = “XXX” to indicate an

error in the frequency setting.

Rxx

Tag decoder range (distance) for ATA tags, xx = 00 to 1F hexadecimal range value

Gxx

Tag decoder range (distance) for SeGo protocol tags, xx = 00 to 1F hexadecimal range

value

Axx

RF power attenuation, where 00 is maximum output power and 0A is minimum output

power (10dB less than maximum power).

I04

Fixed

For example, if factory default settings are assigned, the reader message is

RFST C1 O0 T1 Fxxx R1F G1F A00 I04

Chapter 5 Commands

TransCore Proprietary

5–69

Содержание MPRX 10-7200-001











































































































































Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Похожие инструкции для MPRX 10-7200-001

Бренды по названию

Популярные бренды

TransCore MPRX 10-7200-001, Руководство пользователя

Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Похожие инструкции для MPRX 10-7200-001

Бренды по названию

Популярные бренды