TransCore MPRX 10-7200-001 Скачать руководство пользователя страница 56

Страница: 56 / 138

Chapter 5 Commands

Default Settings

The MPRX is delivered from the factory with specified default settings that determine how the reader

operates. Commands transmitted by the host device can change the default settings and control

additional features. The commands can be transmitted by manually entering the commands at the host

keyboard if the host is in terminal emulation mode. The MPRX can also communicate with ASCII terminals.

Operating Modes

The MPRX has three modes of operation: Data, Command, and Download. The software for the MPRX

contains two separate programs — Boot and Application. The Boot program has control of the MPRX on

startup and when operating in download mode. The Application program has control of the MPRX during

data mode and command mode operation and holds the application code. Together, they control the

MPRX in the three modes of operation.

Data Mode

The MPRX is in the data mode upon power-up. While in the data mode, the MPRX sends all

communications, such as tag IDs and reports, as data messages to the host device. Reports provide

information on input status changes (input 0 and input 1), a presence without tag report, and buffer overflow

information. When MPRX mode has been enabled

(#837)

and while the MPRX is in data mode, the host

device can send the following commands the MPRX:

#01

changes the MPRX from the data mode to the command mode.

#440

provides a one-time reset of all tag uniqueness timers at which point the previously set

timeout interval resumes.

#8110

turns on RF port 0 and sends the command on Ctag pin 0 to fire off Ctag address 0.

#8111

turns on RF port 1 and sends the command on Ctag pin 0 to fire off Ctag address 1.

#8112

turns on RF port 2 and sends the command on Ctag pin 1 to fire off Ctag address 0.

#8113

turns on RF port 3 and sends the command on Ctag pin 1 to fire off Ctag address 1.

#8150

sets the check tag address to 0 on check tag pin 0.

#8151

sets the check tag address to 1 on check tag pin 0.

#8152

sets the check tag address to 0 on check tag pin 1.

#8153

sets the check tag address to 1 on check tag pin 1.

Note:

The MPRX transmits ID codes to the host device when the MPRX is in data mode.

MPRX User Guide

TransCore Proprietary

5–56

Содержание MPRX 10-7200-001











































































































































Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Бренды по названию

Популярные бренды

TransCore MPRX 10-7200-001, Руководство пользователя

Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Бренды по названию

Популярные бренды