TransCore MPRX 10-7200-001 Скачать руководство пользователя страница 11

Страница: 11 / 138

Licensing Requirements

An FCC license provides the user with the legal authorization to operate the MPRX on the licensed

frequencies at the site specified in the license. Only an authorized installer or service technician can set

the RF frequency of the MPRX to the frequency specified in the FCC site license. No end-user-operated

controls exist on the MPRX.
The FCC license may provide the user with protection and authorization to maintain the system should any

other RFID product be used in the licensed area after the MPRX equipment is installed.
Users of the MPRX in the United States must obtain a license from the FCC. In the United States, the

authorized modulated (SeGo protocol operation) frequency band for this product is 911.75 to 919.75 MHz

and the authorized continuous wave (AAR-formatted operation) frequency band is 902.25 to 903.75 MHz

and 910.00 to 921.50 MHz.
The user is responsible for filing the FCC license according to FCC regulations, but the TransCore dealer

will provide assistance and support as necessary to complete these forms. Forms are available online at

the FCC internet site

http://wireless.fcc.gov/uls

. For further information on obtaining the license contact

TransCore.

CAUTION

This equipment can be set to frequency ranges outside those authorized for use in the U.S. by

the FCC. Users in all countries should check with the appropriate local authorities for licensing
requirements.

TransCore Proprietary

Содержание MPRX 10-7200-001











































































































































Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Бренды по названию

Популярные бренды

TransCore MPRX 10-7200-001, Руководство пользователя

Результаты поиска

Содержание MPRX 10-7200-001

Отзывы:

Бренды по названию

Популярные бренды