TransCore AI1422E Скачать руководство пользователя страница 49

Страница: 49 / 102

feature, the rail car’s ID would be reported every 2 minutes (each time the timeout

clock expired).

450 Disable Wiegand Mode (Factory Default)

!450

is a default set in the factory to disable Wiegand mode.

Reader response:

!Done

451 Enable Wiegand Mode

!451

enables Wiegand mode, which allows the reader to transmit data in a format that

emulates the output of a magnetic card reader.
In Wiegand mode, the reader transmits Wiegand-formatted tag data through the

Wiegand interface and ASCII data (the reader accepts reader commands and responds)

through the serial port interface. The reader outputs data from Wiegand-programmed

tags via the Wiegand interface. Tags that are not Wiegand-formatted are not transmitted

through the Wiegand interface or the serial port when in Wiegand mode, although the

tag lock relay is activated on any tag acquired.

Reader response:

!Done

452 Disable Tag Translation Mode (Factory Default)

!452

disables tag translation mode. Incoming full-frame tags will be directly converted to

ASCII. They will not be translated from Association of American Railroads (AAR) and

American Trucking Associations (ATA) format to ASCII.

Reader message:

!Done

453 Enable Tag Translation Mode

!453

enables the translation of tags in AAR and ATA formats. Specific data fields, such as

owner ID and car number, will be extracted from these tags, translated according

to AAR or ATA standards, and converted to ASCII. Tags that are not programmed in

AAR or ATA format will be directly converted to ASCII. The reader will not attempt to

translate data from half-frame or dual-frame tags.

Reader message:

!Done

480 Disable ATA

!480

Disables the reader from reading ATA protocol tags.

481 Enable ATA

!481

enables the reader to read ATA protocol data from tags.

Chapter 6 Commands

TransCore Proprietary

6–33

Содержание AI1422E







































































































Результаты поиска

Содержание AI1422E

Отзывы:

Бренды по названию

Популярные бренды

TransCore AI1422E, Руководство пользователя

Результаты поиска

Содержание AI1422E

Отзывы:

Бренды по названию

Популярные бренды