Trane Voyager Commercial, Инструкция по установке, эксплуатации и обслуживанию

Страница: 106 / 156

106 RT-SVX34R-EN
bank is fired at full fire and the modulating bank again
adjusts to the heating load present.
Check both ignition systems (if applicable) when going
through the test procedures.
Once the ignition system and ignitors have been
checked, open the main power disconnect switch to
reset the RTRM.
W WA AR RN NIIN NG G
H Ha azza arrd do ou uss G Ga asse ess a an nd d F Flla am mm ma ab blle e
V Va ap po orrss!!
F Fa aiillu urre e tto o o ob bsse errv ve e tth he e ffo ollllo ow wiin ng g iin nssttrru uccttiio on nss cco ou ulld d
rre essu ulltt iin n e ex xp po ossu urre e tto o h ha azza arrd do ou uss g ga asse ess,, ffu ue ell
ssu ub bsstta an ncce ess,, o orr ssu ub bsstta an ncce ess ffrro om m iin ncco om mp plle ette e
cco om mb bu ussttiio on n,, w wh hiicch h cco ou ulld d rre essu ulltt iin n d de ea atth h o orr sse erriio ou uss
iin njju urry y.. T Th he e sstta atte e o off C Ca alliiffo orrn niia a h ha ass d de ette errm miin ne ed d tth ha att
tth he esse e ssu ub bsstta an ncce ess m ma ay y cca au usse e cca an ncce err,, b biirrtth h d de effe eccttss,,
o orr o otth he err rre ep prro od du uccttiiv ve e h ha arrm m..
IIm mp prro op pe err iin nsstta alllla attiio on n,, a ad djju ussttm me en ntt,, a alltte erra attiio on n,,
sse errv viicce e o orr u usse e o off tth hiiss p prro od du ucctt cco ou ulld d cca au usse e
fflla am mm ma ab blle e m miix xttu urre ess o orr lle ea ad d tto o e ex xcce essssiiv ve e cca arrb bo on n
m mo on no ox xiid de e.. T To o a av vo oiid d h ha azza arrd do ou uss g ga asse ess a an nd d
fflla am mm ma ab blle e v va ap po orrss ffo ollllo ow w p prro op pe err iin nsstta alllla attiio on n a an nd d
sse ettu up p o off tth hiiss p prro od du ucctt a an nd d a allll w wa arrn niin ng gss a ass p prro ov viid de ed d
iin n tth hiiss m ma an nu ua all..
Turn the main gas supply to the unit “On” and check
the gas pressure at the unit's gas train. Refer to
“Installation Piping,” p. 40 for the proper gas supply
pressure and Figure 35, p. 41 for the location of the gas
pressure taps.
Close the main power disconnect switch and start the
first stage heating Test again. Wait approximately 60
seconds for the heater to switch to low fire and check
the manifold gas pressure. The manifold pressure for a
two stage burner must be set at negative 0.2" w.c., +/-
0.05" w.c. The manifold pressure on a modulating
burner should be set at a positive 0.5" w.c., +/-0.05” w.
c. For modulating burners, expect to see the manifold
pressure reading fluctuate while the burner is
operating, but it should never read negative.
W WA AR RN NIIN NG G
H Ho ott S Su urrffa acce e!!
F Fa aiillu urre e tto o ffo ollllo ow w iin nssttrru uccttiio on nss b be ello ow w cco ou ulld d rre essu ulltt iin n
sse ev ve erre e b bu urrn nss..
S Su urrffa acce e tte em mp pe erra attu urre ess m ma ay y e ex xcce ee ed d 3 30 00 0°°F F ((1 15 50 0°°C C))..
T To o a av vo oiid d p po ossssiib blle e sskkiin n b bu urrn nss,, sstta ay y cclle ea arr o off tth he esse e
ssu urrffa acce ess.. IIff p po ossssiib blle e,, a allllo ow w ssu urrffa acce ess tto o cco oo oll b be effo orre e
sse errv viicciin ng g.. IIff sse errv viicciin ng g iiss n ne ecce essssa arry y w wh hiille e ssu urrffa acce e
tte em mp pe erra attu urre ess a arre e ssttiillll e elle ev va atte ed d,, y yo ou u M MU US ST T p pu utt o on n
a allll P Pe errsso on na all P Prro otte eccttiiv ve e E Eq qu uiip pm me en ntt ((P PP PE E))..
Jump the test terminals momentarily to initiate second
stage heat operation. The combustion blower motor
should go to high speed. The second stage of heat in
units with modulating gas will initiate the second
heater bank to fire and both banks will operate at high
fire. The manifold pressures of the two heater banks in
a high heat modulating unit will be different. The
pressure setting of the two stage burner will be a
negative 0.2" w.c., while the modulating burner will be
a positive 0.05" w.c.
N No otte e:: When firing a modulating unit for the first time, a
“humming”, or resonance sound may be heard.
This is an operational sound made by the burner
screen as it burns in. This sound is not a concern
unless it persists longer than the first few times
the unit is fired.
Electric Heat Units
Start the service test and check the amperage draw for
each heating stage. Refer to the heater electrical data in
Table 9, p. 29 (60 Hz) and Table 13, p. 31 (50 Hz) for the
full load amps of a specific heater size.
Once the operation of the heaters have been checked,
open the main power disconnect switch or the unit
mounted disconnect switch to shut the unit “Off” and
to reset the RTRM.
This concludes the setup and testing for the major
components and controls within the unit. Follow the
Test guide in
, p. 68 - Table 46, p. 74 to verify that the
optional VFD, economizer actuator, and minimum
ventilation controls are functioning.
Final Unit Checkout
After completing all of the checkout and startup
procedures outlined in the previous sections (i.e.,
operating the unit in each of its modes through all
available stages of cooling and heating), perform these
final checks before leaving the unit:
Verify that the RTRM is in the normal operation mode.
The LED located on the UCP module is “on” and
glowing continuously.
For Variable Air Volume Units
For Constant Volume Units
Verify that the “Mode” selection switch and the “Zone
Temperature” setpoints are set and/or programmed at
the sensor modules.
For Variable Air Volume Units
The RTAM has input setpoint potentiometers inside the
control panel that are set at the factory which will allow
the unit to operate and maintain system control. For
specific job specifications;
• Verify that the control input potentiometers are set
according to the job specifications, i.e.;
– Outside air reset temperature - _______ Setpoint
– Reset amount °F. - _______ Setpoint
– Static pressure - _______ Setpoint
S Stta arrttu up p