background image

Model Number Description

6

RT-SVX22M-EN

D

Discharge Air Sensing

14

and

Condensate Drain Pan Overflow
Switch

E

Clogged Filter Switch

14

, Fan Failure

Switch

14

and Condensate Drain Pan

Overflow Switch

F

Clogged Filter Switch

14

, Discharge

Air Sensing Tube

14

and Condensate

Drain Pan Overflow Switch

G

Fan Failure Switch, Discharge Air
Sensing Tube

14

and Condensate

Drain Pan Overflow Switch

H

Clogged Filter Switch

14

, Fan Failure

Switch

14

, Discharge Air Sensing

14

and Condensate Drain Pan Overflow
Switch

Digit 26 - System Monitoring
Controls

0

No Monitoring Controls

A

Demand Control Ventilation
(CO

2

)

30

,

31

Digit 27 - Unit Hardware
Enhancements

0

No Enhancements

1

Stainless Steel Drain Pan

Digit 31- Advanced Unit
Controls

0

Standard Unit Controls

1

Human Interface

Model Number Notes

1.

Available on 3-5 ton models.

2. Crankcase heaters are optional

on TSC (036, 048, 060, 072, 090,
102, 120); standard on THC (036,
048, 060, 072, 092, 102, 120).

3. Not available with

electromechanical controls.

4. Manual outside air damper will

ship factory supplied within the
unit, but must be field installed.

5. High pressure control is standard

on all units.

6. On 3-5 ton, multispeed direct

drive is standard on single phase
and 15 SEER. On 6-10 ton,
multispeed direct drive is
standard on all 10 ton and 7.5-8.5
ton high efficiency. Belt drive is
standard on all other units.

7.

Economizer with Barometric
Relief is for downflow configured
units only. Order Economizer
without Barometric Relief for
horizontal configuration.
Barometric Relief for horizontal
configured units must be ordered
as field installed accessory.

8. Through the base electric

required when ordering
disconnect/circuit breaker
options.

9. Requires use of Disconnect or

Circuit Breaker.

10. Standard metering devices are

TXVs.

11. Frostat cannot be field installed in

electro-mechanical units.

12. The return air smoke detector

may not fit up or work properly on
the Precedent units when used in
conjunction with 3rd party
accessories such as bolt on heat
wheels, economizers and power
exhaust. Do not order the return
air smoke detectors when using
this type of accessory.

13. Return Air Smoke Detector

cannot be ordered with Novar
Controls.

14. These options are standard when

ordering Novar Controls.

15. This option is used when

ordering Novar Controls.

16. Not available with high

temperature duct sensor
accessory.

17. Digit 15 = 2

18. Novar Sensor utilized with

Digit 21 = (4) Novar 3051 Controls
without Zone Sensor.

19. Available for 10 ton standard

efficiency models only.

20. Available for 3, 4, 5, 6, 7½, 8½ ton

standard/high efficiency models
only.

21. Requires selection of 2” Pleated

Filters (option B or C) for Digit 16.

22. Not available on 6 ton units and

all single phase or standard
efficiency.

23. Standard on TSC 6, 7½ (single

and dual systems), 8½, 10 ton
standard efficiency models and

THC 4, 5, 6, 7½, 8½ ton high

efficiency models (except for 3, 4,
5, 6 and 10 ton dehumidification
models).

24. Epoxy coil and epoxy with

hailguard options are not
available for units with
microchannel condenser coil.

25. Single Zone VAV is only available

on 7.5-10 ton high efficiency and
10 ton standard efficiency
products with ReliaTel™ controls.

26. Multi-speed indoor fan available

only on 7.5 & 8.5 ton high
efficiency, and 10 ton products
with ReliaTel™ controls.

27. Motorized Outside Air Damper is

not available on Multi-Speed or
SZVAV (Single Zone Variable Air

Volume) products.

28. Frostat standard on Multi-Speed

and SZVAV (Single Zone Variable

Air Volume) products.

29. Novar is not available with SZVAV

products.

30. Demand Control Ventilation not

available with electromechanical
controls.

31. Demand Control Ventilation

Option includes wiring only. The
C0

2

sensor is a field-installed only

option.

32. Discharge Air Sensing is also

standard equipment on units
with Single Zone and Supply Air

Temperature Control VAV.

Digit 15 = 0

Standard Efficiency
1 Phase = High Efficiency Multispeed Direct 
Drive Motor
3 Phase (3-8½ Ton) = Belt Drive

3 Phase (10 Ton) = Ultra High Efficiency Direct 
Drive Plenum Fan
High Efficiency
1 Phase = High Efficiency Multispeed Direct 

Drive Motor
3 Phase (3-5 ton) = High Efficiency Multispeed 
Direct Drive Motor

3 Phase (3-5 ton w/Dehumidification) = Belt 

Drive Motor
3 Phase (7½-10 ton) = Ultra High Efficiency 

Direct Drive Plenum Fan

Not Available

Standard Efficiency

10 Ton w/575V

High Efficiency
3-5 ton w/Standard Indoor Motor w/460V

Standard Efficiency
1 Phase = Not Available

3 Phase = Not Available
High Efficiency
1 Phase = Not Available

3 Phase (3-5 ton) = May be Ordered
3 Phase (3-5 ton w/Dehumidification) = Not 
Available

3 Phase (6-10 ton) = Not Available

Содержание TSC037E





































































Отзывы: