background image

Installation

28

RT-SVX22M-EN

Note:

If unit is equipped with Return Air Smoke Detector,
refer to field conversion instructions for horizontal
discharge before installing return air duct.

Note:

If unit is equipped with Discharge Air Sensing
option refer to the following figure for proper tube
positioning based on unit tonnage.

Note:

Certain unit/electric heater combinations require a
limit switch change out for horizontal airflow
applications. Refer to the following instructions to
determine if this process is required for the unit
undergoing installation.

6. After completing installation of the duct covers for

horizontal discharge, proceed to TCO-A instructions.

TCO-A Instructions

If the unit being installed is listed in the following table and
is equipped with the corresponding model number of
factory installed electric heater package in the table, the
limit control TCO-A must be replaced with the extra limit
control shipped in the heater compartment. ReplaceTCO-

A following the instructions in steps 1 through 3 below. If

the unit being installed does not have a factory installed
electric heater package or is equipped with a factory
installed electric heater model that does not correspond to

any in this table, skip steps 1 through 3 and go on to next
step in the installation process.

1.

Remove the heater section access panel and open the
electric heater dead front panel.

2. TCO-A is the limit control located in the central part of

the heater mounting plate and that is located on the
bottom of the two heater element assemblies. To
replace this device, first remove the two wires
connected to the terminals. Next, remove the two
screws which secure it to the heater element mounting
plate. OnceTCO-A has been removed form the heater
element mounting plate, discard this device.

3. Obtain the replacement TCO-A which is secured by a

wire tie near the electric heater terminal block in the
heater compartment. Attach it to the heater element
mounting plate with the two screws that were removed
in step 2 above. Connect the two wires that were un-
hooked in step 2 to the terminals on the new TCO-A.
Refer to the heater package wiring diagram to assure
that the wiring is connected properly.

4. Close the electric heater dead front panel and replace

heat section access panel.

Figure 29.

Discharge air sensor

Figure 30.

Supply & return openings

Downflow application

Horizontal application

Cap assembly
with insulation

Remove and discard this tube 
for horizontal conversion

Cap assembly 
with insulation

Secure with screw

Insulation side 
down

Supply duct cover

Insulation side up

Return duct 
cover

Table 4.

TCO-A replaced for horizontal duct

configuration

Unit Model 

Number

Electric Heater 

Model Number

TCO-A location

TSC120F4, THC092-

102F

BAYHTRA418, 427, 

436, 454

Right

TSC120FW

BAYHTRAW18A, 36A, 

54A

Right

THC072F4

BAYHTRU427, 436

Center

TSC090F4

BAYHTRW427, 436

Center

TSC090FW

BAYHTRWW27, W36

Center

Figure 31. TCO-A location

Содержание TSC037E





































































Отзывы: