Trane Tracer ZN.520 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 118

background image

CNT-SVX04A-EN

16

Binary outputs

General description

Refer to Tables 4 and 5 on page 13 for
terminal identification and typical usage.

The Tracer ZN.520 zone controller is a high-end modulating controller that supports
the economizer and discharge air tempering functions of terminal products. The
controller may be configured and applied to fan coil, blower coil, or unit ventilator
configurations. The configuration of binary outputs is largely based on the unit
configuration. Refer to Table 8 for possible functions for each binary output.

Binary outputs are configured to support the following:

■

Three fan stages (when one or two fan stages are present, medium fan
speed can be configured as exhaust fan)

■

One hydronic cooling stage

■

One hydronic heating stage (dehumidification requires this to be in the
reheat position)

■

One DX cooling stage

■

One- or two-stage electric heat (dehumidification requires this to be in the
reheat position)

■

Face and bypass damper

■

Modulating outdoor air damper

■

One baseboard heat stage

Table 8

Configuration of binary outputs

Note

1

:

For Tracer ZN.520 zone controller units configured and applied as 2-pipe hydronic heat/cool

changeover, terminals J1-5 and J1-6 are used to control the primary valve for both heating and cooling.

J1-1

Fan high

J1-2

Fan medium/Exhaust fan

J1-3

Fan low

J1-4

(Key)

J1-5

Cool valve—open, or 2 position valve, or DX compressor output

1

J1-6

Cool valve—close

1

J1-7

Face and bypass damper—open

J1-8

Face and bypass damper—close

J1-9

Heat valve—open, or 2 position valve, or 1

st

electric heat stage

1

J1-10

Heat valve—close or 2

nd

electric heat stage

1

J1-11

Outdoor air damper—open

J1-12

Outdoor air damper—close

TB4-1

Generic/Baseboard heat output

TB4-2

24 VAC

«
...
16
17
18
19
20
...
»

Содержание Tracer ZN.520























































































































Отзывы:

Нет отзывов

Похожие инструкции для Tracer ZN.520

Бренд: NCR Страницы: 6

Бренд: jbc Страницы: 4

Бренд: Samson Страницы: 56

Бренд: Hach Страницы: 128

Бренд: Yamato Страницы: 33

Бренд: Saga Страницы: 9

Бренд: Häfele Страницы: 2

Бренд: Häfele Страницы: 24

Бренд: VAT Страницы: 27

MorphoAccess SIGMA Extreme Series

Бренд: Idemia Страницы: 31

Бренд: ICP DAS USA Страницы: 148

Бренд: ICMA Страницы: 8

Бренд: J+J Страницы: 4

Бренд: Val Controls Страницы: 6

EP Series Pro-Bloc

Бренд: Parker Страницы: 11

Бренд: Parker Страницы: 22

Бренд: Parker Страницы: 2

SYSMAC C500-NC222-E

Бренд: Omron Страницы: 164

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды