background image

X-XX UL

INSTALLATION INSTRUCTIONS

®U.S. Registered Trademark  •            •   All Rights Reserved

Multistage

Electronic Thermostat

TAYSTAT 375

APPLICATION

The TAYSTAT 375 Multistage  Electronic Thermostat provides electronic control of 24 Vac two-stage heating and two-
stage cooling systems. Refer to Table 1 for a general description of the thermostat. The thermostat requires a common
wire to supply power.

Table 1. Thermostat Description.

MERCURY NOTICE

If this control is replacing a control that contains
mercury in a sealed tube, do not place your old
control in the trash. Dispose of properly.

Contact your local waste management authority for
instructions regarding recycling and the proper
disposal of the old control.

INSTALLATION

When Installing this Product...

1. Read these instructions carefully. Failure to follow

the instructions can damage the product or cause a
hazardous condition.

2. Check the ratings given in the instructions and on

the product to make sure the product is suitable for
your application.

3. Installer must be a trained, experienced service

technician.

4. After completing installation, use these instructions

to check out the product operation.

CAUTION

Electrical Shock or Equipment Damage Hazard.
Can shock individuals or short equipment
circuitry.
Disconnect power supply before installation.

Location

Install the thermostat about 5 ft (1.5m) above the floor in
an area with good air circulation at average temperature.
See Fig. 1.

Do not install the thermostat where it can be affected by:

drafts, or dead spots behind doors and in corners.

hot or cold air from ducts.

radiant heat from sun or appliances.

concealed pipes and chimneys.

unheated (uncooled) areas such as an outside wall
behind the thermostat.

Wallplate Installation

Mount the thermostat horizontally on the wall or on a 2 in.
x 4 in. wiring box.

1. Position and level the wallplate (for appearance

only). The thermostat functions properly even when
not level.

Pub. No. 18-HD28D1-1

TAYSTAT  

System

Changeover

System  

Selection

Fan

Selection

Comments

375

Heat-Cool

Automatic

Heat-Off-Cool-Auto

On-Auto

Use keyboard to make system and fan
selections.

69-1592-1

Содержание TAYSTAT 375













Отзывы: