Trane Precedent YZC036E Скачать руководство пользователя страница 13

Страница: 13 / 60

RT-SVX46G-EN

Pre-Installation

Precautionary Measures

•

Avoid breathing fiberglass dust.

•

Use a NIOSH approved dust/mist respirator.

•

Avoid contact with the skin or eyes. Wear long-
sleeved, loose-fitting clothing, gloves, and eye
protection.

•

Wash clothes separately from other clothing: rinse
washer thoroughly.

•

Operations such as sawing, blowing, tear-out, and
spraying may generate fiber concentrations requiring
additional respiratory protection. Use the appropriate
NIOSH approved respiration in these situations.

First Aid Measures

Eye Contact

- Flush eyes with water to remove dust. If

symptoms persist, seek medical attention.

Skin Contact

- Wash affected areas gently with soap and

warm water after handling.

WARNING

Fiberglass Wool!

Exposition to glass wool fibers without all necessary

PPE equipment could result in cancer, respiratory, skin

or eye irritation, which could result in death or serious

injury. Disturbing the insulation in this product during

installation, maintenance or repair will expose you to

airborne particles of glass wool fibers and ceramic

fibers known to the state of California to cause cancer

through inhalation. You MUST wear all necessary

Personal Protective Equipment (PPE) including gloves,

eye protection, a NIOSH approved dust/mist respirator,

long sleeves and pants when working with products

containing fiberglass wool.

Содержание Precedent YZC036E





























































Результаты поиска

Содержание Precedent YZC036E

Отзывы:

Похожие инструкции для Precedent YZC036E

Бренды по названию

Популярные бренды

Trane Precedent YZC036E, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Precedent YZC036E

Отзывы:

Похожие инструкции для Precedent YZC036E

Бренды по названию

Популярные бренды