background image

Installation

RT-SVX46G-EN

25 

Roof Curb

Downflow

The roof curbs for these units consists of a “full perimeter” 
enclosure to support the unit just inside of the unit base 
rail.
Before installing any roof curb, verify:

It is the correct curb for the unit.

It includes the necessary gaskets and hardware.

The purposed installation location provides the 
required clearance for proper operation.

The curb is level and square and the top surface of the 
curb must be true to assure an adequate curb-to-unit 
seal.

Verify that appropriate materials were used in the 
construction of roof and ductwork. Combustible materials 
should not be used in the construction of ductwork or roof 
curb that is in close proximity to heater elements or any 
hot surface. Any combustible material on the inside of the 
unit base should be removed and replaced with 
appropriate material. 
Step-by-step curb assembly and installation instructions 
ship with each accessory roof curb kit. Follow the 
instructions carefully to assure proper fit-up when the unit 
is set into place.

Figure 41. 3 tons ultra high efficiency - downflow airflow 

supply/return - through-the-base utilities

(a)

(a) All dimensions are in inches/millimeters.

Figure 42. 4 to 5 tons ultra high efficiency- downflow 

airflow supply/return - through-the-base 
utilities

(a)

(a) All dimensions are in inches/millimeters.

Figure 43. Cooling and gas/electric - 6 to 8.5 tons ultra 

high efficiency - downflow supply/return 
through-the-base utilities

Note:

All dimensions are in inches/millimeters.

THROUGH 

THE BASE GAS

(Y_C Models only)

THROUGH 
THE BASE 

ELECTRICAL

SUPPLY

RETURN

TBU CONDENSATE

3 5/8”

92 MM

14”

356 MM

9 1/4”

235 MM

15 1/2”

394 MM

4”

102 MM

24”

610 MM

18”

457 MM

27 9/16”

701 MM

4 3/16”

106 MM

4 9/16”

116 MM

23 1/2”

597 MM

2 13/16”

71 MM

6 1/2”

165 MM

3 11/16”

94 MM

4 7/8”

124 MM

5 1/16”

128 MM

9 15/16”

253 MM

4”

102 MM

3 5/8”
92 MM

17 1/2”
444 MM

9 7/8”

251 MM

17 1/2”
444 MM

32 1/8”
816 MM

33”

838 MM

RETURN

SUPPLY

THROUGH THE

BASE CONDENSATE

4 1/8”

104 MM

27 5/8”
701 MM

40 3/4”

1035 MM

4 5/8”

119 MM

THROUGH THE

BASE ELECTRICAL

5 7/8”

149 MM

10 7/8”
276 MM

5”

127 MM

3 3/4”
95 MM

2 3/4”
71 MM

6 1/2”

165 MM

THROUGH THE

BASE GAS

3 5/8”
92 MM

17 1/2”
444 MM

4”

102 MM

9 7/8”

251 MM

17 1/2”
444 MM

32 1/8”
816 MM

RETURN

SUPPLY

33”

838 MM

4 1/8”

104 MM

27 5/8”
701 MM

THROUGH THE 

BASE CONDENSATE

40 3/4”

1035 MM

THROUGH THE 

BASE ELECTRICAL

5 7/8”

149 MM

5”

127 MM

10 7/8”
276 MM

3 3/4”
95 MM

2 3/4”
71 MM

6 1/2”

165 MM

Figure 44. Cooling and gas/electric - 10 tons ultra high 

efficiency - downflow airflow supply/return, 
through-the-base utilities

Note:

All dimensions are in inches/millimeters.

WARNING

Combustible Materials!

Failure to maintain proper clearance between the unit 

heat exchanger, vent surfaces and combustible 

materials could cause a fire which could result in death 

or serious injury or property damage. Refer to unit 

nameplate and installation instructions for proper 

clearances.

              

 

 

  

 

RETURN

RETURN

SUPPLY

SUPPLY

3 5/8”

3 5/8”
92 MM

92 MM

17 1/2”

17 1/2”
444 MM

444 MM

9 7/8”

9 7/8”

251 MM

251 MM

17 1/2”

17 1/2”
444 MM

444 MM

32 1/8”

32 1/8”
816 MM

816 MM

33”

33”

838 MM

838 MM

4”

4”

102 MM

102 MM

THROUGH THE 

THROUGH THE 

BASE ELECTRICAL

BASE ELECTRICAL

THROUGH THE 

THROUGH THE 

BASE CONDENSATE

BASE CONDENSATE

4 5/8”

4 5/8”

119 MM

119 MM

THROUGH THE

THROUGH THE

BASE GAS

BASE GAS

5 7/8”

5 7/8”

149 MM

149 MM

27 5/8”

27 5/8”
701 MM

701 MM

42 3/16”

42 3/16”
1072 MM

1072 MM

6 3/8”

6 3/8”

163 MM

163 MM

2 3/4”

2 3/4”
71 MM

71 MM

51 3/16”

51 3/16”
1316 MM

1316 MM

4 1/8”

4 1/8”

104 MM

104 MM

Содержание Precedent YZC036E





























































Отзывы: