TTA-R410A
9
Refrigerant Charging and Evacuation
Note:
Each TTA unit ships with holding charge.
System Evacuation
1. After completion of leak check,
evacuate the system.
2. Attach appropriate hoses from
manifold gauge to gas and liquid
line pressure taps.
Note:
Unnecessary switching of
hoses can be avoided and complete
evacuation of all lines leading to
sealed system can be accomplished
with manifold center hose and
connecting branch hose to a cylinder
of R-22/R407C and vacuum pump.
3. Attach center hose of manifold
gauges to vacuum pump.
4. Evacuate the system to hold a
350 micron (-76 cm.Hg) vacuum.
5. Close off valve to vacuum pump
and observe the micron gauge.
If gauge pressure rised above
500 microns in one (1) minute,
then evacuation is incomplete or
the system has a leak.
6. If vacuum gauge does not rise
above 500 microns in one (1)
minute, the evacuation should be
complete.
Caution:
Do not connect a
dual-circuit outdoor unit to a single
circuit evaporating unit. (blower)
!
TTA 120 JDF
TTA 150 JDF
TTA 150 JD00
TTA 180 JD00
TTA 200 JD00
TTA 240 JD00
TTA 180 JD0G
TTA 200 JD0G
TTA 240 JD0G
TTA B51 JDF
TTA B65 JDF
TTA 075 JDF
5.40
11.90
3.30
7.27
3.90
8.60
6.30
13.89
6.30
13.89
6.10
13.45
5.40
11.90
6.75
14.88
6.75
14.88
13.50
29.76
12.60
27.78
12.20
26.90
10.30
23.81
TTA 100 JDF
Tubing Sizes
Additional
Additional
See
Suction
Liquid
Tubing Length
Refrigerant
Note
1 1/8"
3/8"
15 ft.
0 lb.
11.5 oz.
(1)
1 1/8"
3/8"
25 ft.
1 lb.
3.0 oz.
(1)
1 1/8"
3/8"
32 ft.
1 lb.
8.0 oz.
(1)
1 1/8"
3/8"
40 ft.
1 lb.
14.0 oz.
(1)
1 3/8"
1/2"
15 ft.
1 lb.
4.0 oz.
(2)
1 3/8"
1/2"
25 ft.
2 lb.
1.0 oz.
(2)
1 3/8"
1/2"
32 ft.
2 lb.
11.0 oz.
(2)
1 3/8"
1/2"
40 ft.
3 lb.
5.0 oz.
(2)
1 5/8"
5/8"
15 ft.
1 lb.
15.5 oz.
(3)
1 5/8"
5/8"
25 ft.
3 lb.
5.5 oz.
(3)
1 5/8"
5/8"
32 ft.
4 lb.
3.2 oz.
(3)
1 5/8"
5/8"
40 ft.
5 lb.
4.0 oz.
(3)
1
of 1 1/8" and 3/8" lines.
2
Amounts shown are based on 1.33 ounces of refrigerant per foot
of 1 3/8" and 1/2" lines.
3
Amounts shown are based on 2.1 ounces of refrigerant per foot
of 1 5/8" and 5/8" lines.
Note:
for tubing over 40 ft. calculate the additional refrigerant needed,
based on notes above.
Table 4 - Additional Required Refrigerant
Amounts shown are based on 0.75 ounces of refrigerant per foot
7. Remove vacuum pump. Attach
center hose of manifold gauge to
cylinder, purge the charging
line, open valve on cylinder
and allow refrigerant pressure to
build up to about 40 psig.
8. Close valve on the supply
cylinder and close valves on
manifold gauge.
9. Leak test the entire system. Using
proper procedures and caution,
repair any leaks found and repeat
the leak test.
Содержание ODYSSEY TTA 051 JDF
Страница 21: ...TTA R410A 21 Dimensional Data TTA 075 100 120 JDF SINGLE CIRCUIT HORIZONTAL AND VERTICAL DISCHARGE...
Страница 22: ...22 TTA R410A Dimensional Data TTA 150 JDF SINGLE CIRCUIT HORIZONTAL AND VERTICAL DISCHARGE...
Страница 23: ...TTA R410A 23 Dimensional Data TTA 150 180 200 240 JD00 DUAL CIRCUIT...
Страница 24: ...24 TTA R410A Dimensional Data TTA 150 180 200 240 JD0G MANIFOLDED COMPRESSOR...
