Trane IntelliPak SCRG-020 Скачать руководство пользователя страница 46

Страница: 46 / 52

DIAGNOSTICS Menu

PKG-SVP01E-EN

Active Diagnostic -- Manual Reset

Used With: All units
Factory Presets: N/A

___________________ More

Possible Values:

Low Pressure Control Open - Ckt 1, Ckt 2, Ckt 3, Ckt 4 Manual Reset SA Static Pressure Limit

Compressor Contactor Fail - Ckt 1, Ckt 2, Ckt 3, Ckt 4

Low Air Temperature Limit Trip

Compressor Trip - Ckt 1, Ckt 2, Ckt 3, Ckt 4

Emergency Stop

Note:

The word “MORE” will appear on the screen if more than one failure has occurred.

Active Diagnostic -- Auto Reset

___________________ More

Possible Values:

RTM Zone

Heat Aux Temp

Supply Air Temp

Unocc Zone Cool Setpoint

RTM Aux. Temp

Unocc Zone Heat Setpoint

OA Temp

Supply Air Pres Setpt

Mode Input

Space Pressure Pres Setpt

Occ Zone Cool Setpoint

Space Pressure

Occ Zone Heat Setpoint

Return Air Temp

Supply Air Pres

RA Humidity

OA Humidity

Auto Reset SA Static Pres
Limit

SCM Communication

Evap Temp - CKT 1, 2, 3, 4

MCM Communication

Heat Module Commun.

ECEM Communication

Cond Temp - CKT 1, 2, 3, 4

TCI Communication

GBAS Module

Communication

Tracer® Communication

NSB Panel Communication

Unit HI Communcation

VOM Communication

Sup Air Temp Cool Setpt

Sup Air Temp Heat Setpt

NSB Panel Zone Temp

Sensor

VCM Aux Temp

Velocity Press

VCM Communication

WSM Communication

Ent Cond Water Temp

Ent Water Temp

WSM Mixe Air Temp

Water Flow

Pressing the "NEXT" key to view the diagnostics will prompt the following screen if a "information only" failure has occurred.

Active Diagnostic -- Info

___________________ More

Possible Values:

Heat Fail

Dirty Filter

Ventilation Override Mode A, B, C, D, or E

RTM Data Storage Error

Note:

Activation of any VOM mode can be viewed within the “Active Diagnostic” screen.

Содержание IntelliPak SCRG-020





















































Результаты поиска

Содержание IntelliPak SCRG-020

Отзывы:

Похожие инструкции для IntelliPak SCRG-020

Бренды по названию

Популярные бренды

Trane IntelliPak SCRG-020, Руководство по программированию

Результаты поиска

Содержание IntelliPak SCRG-020

Отзывы:

Похожие инструкции для IntelliPak SCRG-020

Бренды по названию

Популярные бренды