Trane IntelliPak SCRG-020 Скачать руководство пользователя страница 16

Страница: 16 / 52

Programming Status

PKG-SVP01E-EN

WSM Ent Cond Water Temp Input
Low Water Temp Compressor Lockout

65.2 F
34 F

Used With: All water-cooled units only.
Possible Lockout Values: Lockout Temperature =
0 - 99 F

Pressing the NEXT key will scroll forward through the screens.

Compressor Module Ckt 1
Evap Temp 75.0 F

Sat Cond Temp 81.0 F

Press the NEXT key until the following screen is displayed. (if applicable)

Compressor Module Ckt 2
Evap Temp 72.0 F

Sat Cond Temp 97. 0F

Press the NEXT key until the following screen is displayed.

Compressor Module Ckt 3

Used With: All SCWF/SIWF 35-80 ton units only.

Evap Temp 72.0 F

Sat Cond Temp 97 .0 F

Press the NEXT key until the following screen is displayed.

Compressor Module Ckt 4

Used With: All SCWF/SIWF 60-80 ton units only.

Evap Temp 72.0 F

Sat Cond Temp 97 .0 F

Press the NEXT key until the following screen is displayed.

End of Submenu (NEXT) to Enter SETUP

Press the NEXT key until the following screen is displayed.

Economizer Status Submenu

Used With: Units with a waterside or airside
economizer only.

Press ENTER to View Data in This Submenu

Press the NEXT key until the following screen is displayed.

Water Economizing: DISABLED

Used With: Units with a waterside economizer only.
Possible Values: Economizer = Disable, enable;
Water econ position - opening to/closing to 0-100%

Outside Air Damper Pos:

10%

Press the NEXT key until the following screen is displayed.

WSM Mixed Air Temperature:

68 F

Used With: Units with a waterside economizer or
condenser only.

WSM Entering Water Temperature:

60 F

Pressing the NEXT key will scroll forward through the screens.

Water Econ Bpass Pos:

10%

Used With: Units with a waterside economizer and
condenser only.

Pressing the NEXT key will scroll forward through the screens.

Air Economizing: DISABLED

Used With: Units with an airside economizer only.
Possible Values: Economizer = Disable, enable;
Outside air = opening to/closing to 0-100%

Outside Air Damper Pos:

Pressing the NEXT key will scroll forward through the screens.

Active Outside Air Enthalpy

12.0 BTU/LB

Used With: Units with an airside economizer and
comparative enthalpy only.
Possible Values: 10-99 BTU/LB

ECEM Return Air Enthalpy

34.0 BTU/LB

Pressing the NEXT key will scroll forward through the screens.

Active Outside Air Temperature

86.0 F

Used With: Units with an airside economizer only.

ECEM Return Air Temperature

78.0 F0

Pressing the NEXT key will scroll forward through the screens.

Содержание IntelliPak SCRG-020





















































Результаты поиска

Содержание IntelliPak SCRG-020

Отзывы:

Похожие инструкции для IntelliPak SCRG-020

Бренды по названию

Популярные бренды

Trane IntelliPak SCRG-020, Руководство по программированию

Результаты поиска

Содержание IntelliPak SCRG-020

Отзывы:

Похожие инструкции для IntelliPak SCRG-020

Бренды по названию

Популярные бренды