Trane IntelliPak SCRF 25, Инструкция по установке, эксплуатации и обслуживанию

Страница: 99 / 120

SCXF-SVX01Q-EN 99
5. Use a steam cleaning machine, starting from the
top of the coil and working downward. Clean the
leaving air side of the coil first, then the entering air
side. Use a block-off to prevent steam from blowing
through the coil and into a dry section of the unit.
6. Repeat step 5 as necessary. Confirm that the drain
line is open following completion of the cleaning
process.
7. Allow the unit to dry thoroughly before putting the
system back into service.
8. Straighten any coil fins that may be damaged with a
fin rake.
9. Replace all panels and parts and restore electrical
power to the unit.
10. Ensure that contaminated material does not contact
other areas of the equipment or building. Properly
dispose of all contaminated materials and cleaning
solutions.
Chemical Cleaning of Condenser and
Economizer Coil
Chemical cleaning removes scale deposits built up by
minerals in the water. For a suitable chemical solution,
consult a water treatment specialist. The condenser
water circuit is composed of copper, steel, and cast
iron. The chemical supply house should approve or
provide all materials used in the external circulating
system, along with the quantity of cleaning material,
duration of cleaning time, and safety precautions
necessary for handling the cleaning agent.
Piping Components
Water Valves
W WA AR RN NIIN NG G
H Ha azza arrd do ou uss V Vo olltta ag ge e w w//C Ca ap pa acciitto orrss!!
F Fa aiillu urre e tto o d diisscco on nn ne ecctt p po ow we err a an nd d d diisscch ha arrg ge e
cca ap pa acciitto orrss b be effo orre e sse errv viicciin ng g cco ou ulld d rre essu ulltt iin n d de ea atth h o orr
sse erriio ou uss iin njju urry y..
D Diisscco on nn ne ecctt a allll e elle eccttrriicc p po ow we err,, iin nccllu ud diin ng g rre em mo otte e
d diisscco on nn ne eccttss a an nd d d diisscch ha arrg ge e a allll m mo otto orr sstta arrtt//rru un n
cca ap pa acciitto orrss b be effo orre e sse errv viicciin ng g.. F Fo ollllo ow w p prro op pe err
llo occkko ou utt//tta ag go ou utt p prro occe ed du urre ess tto o e en nssu urre e tth he e p po ow we err
cca an nn no ott b be e iin na ad dv ve errtte en nttlly y e en ne errg giizze ed d.. F Fo orr v va arriia ab blle e
ffrre eq qu ue en nccy y d drriiv ve ess o orr o otth he err e en ne errg gy y sstto orriin ng g
cco om mp po on ne en nttss p prro ov viid de ed d b by y T Trra an ne e o orr o otth he errss,, rre effe err tto o
tth he e a ap pp prro op prriia atte e m ma an nu uffa accttu urre err’’ss lliitte erra attu urre e ffo orr
a allllo ow wa ab blle e w wa aiittiin ng g p pe erriio od dss ffo orr d diisscch ha arrg ge e o off
cca ap pa acciitto orrss.. V Ve erriiffy y w wiitth h a a C CA AT T IIIIII o orr IIV V v vo ollttm me ette err
rra atte ed d p pe err N NF FP PA A 7 70 0E E tth ha att a allll cca ap pa acciitto orrss h ha av ve e
d diisscch ha arrg ge ed d..
F Fo orr a ad dd diittiio on na all iin nffo orrm ma attiio on n rre eg ga arrd diin ng g tth he e ssa affe e
d diisscch ha arrg ge e o off cca ap pa acciitto orrss,, sse ee e P PR RO OD D--S SV VB B0 06 6* *--E EN N..
Water valves have a stern packing nut. If there is
evidence of water leakage at the valve stem, proceed as
follows:
1. Remove actuator motor from support plate.
2. Remove shaft coupling.
3. Torque the packing nut to 10-ft.-lbs. of torque.
4. Replace shaft coupling.
5. Replace actuator motor.
Flow Switch
Flow switches have a magnet on the vane assembly
that attracts ferrous particulate may build up on the
magnet to the point that the vane will wedge and not
operate properly. When the flow switch does not
operate, remove and replace.
Maintenance Periodic Checklists
W WA AR RN NIIN NG G
H Ha azza arrd do ou uss S Se errv viicce e P Prro occe ed du urre ess!!
F Fa aiillu urre e tto o ffo ollllo ow w a allll p prre ecca au uttiio on nss iin n tth hiiss m ma an nu ua all a an nd d
o on n tth he e tta ag gss,, ssttiicckke errss,, a an nd d lla ab be ellss cco ou ulld d rre essu ulltt iin n
d de ea atth h o orr sse erriio ou uss iin njju urry y..
T Te ecch hn niicciia an nss,, iin n o orrd de err tto o p prro otte ecctt tth he em msse ellv ve ess ffrro om m
p po otte en nttiia all e elle eccttrriicca all,, m me ecch ha an niicca all,, a an nd d cch he em miicca all
h ha azza arrd dss,, M MU US ST T ffo ollllo ow w p prre ecca au uttiio on nss iin n tth hiiss m ma an nu ua all
a an nd d o on n tth he e tta ag gss,, ssttiicckke errss,, a an nd d lla ab be ellss,, a ass w we ellll a ass tth he e
ffo ollllo ow wiin ng g iin nssttrru uccttiio on nss:: U Un nlle essss ssp pe ecciiffiie ed d o otth he errw wiisse e,,
d diisscco on nn ne ecctt a allll e elle eccttrriicca all p po ow we err iin nccllu ud diin ng g rre em mo otte e
d diisscco on nn ne ecctt a an nd d d diisscch ha arrg ge e a allll e en ne errg gy y sstto orriin ng g
d de ev viicce ess ssu ucch h a ass cca ap pa acciitto orrss b be effo orre e sse errv viicciin ng g..
F Fo ollllo ow w p prro op pe err llo occkko ou utt//tta ag go ou utt p prro occe ed du urre ess tto o
e en nssu urre e tth he e p po ow we err cca an n n no ott b be e iin na ad dv ve errtte en nttlly y
e en ne errg giizze ed d.. W Wh he en n n ne ecce essssa arry y tto o w wo orrkk w wiitth h lliiv ve e
e elle eccttrriicca all cco om mp po on ne en nttss,, h ha av ve e a a q qu ua alliiffiie ed d lliicce en nsse ed d
e elle eccttrriicciia an n o orr o otth he err iin nd diiv viid du ua all w wh ho o h ha ass b be ee en n
ttrra aiin ne ed d iin n h ha an nd dlliin ng g lliiv ve e e elle eccttrriicca all cco om mp po on ne en nttss
p pe errffo orrm m tth he esse e tta asskkss..
Monthly Checklist
The following check list provides the recommended
maintenance schedule to keep the commercial self-
contained equipment running efficiently.
1. Inspect unit air filters. Clean or replace if airflow is
blocked or if filters are dirty.
2. Inspect coils for excess moisture or icing. Icing on
the coils may indicate low airflow supply, restricted
airflow from dirty fins, evaporator frost protection
sensor problems, or a shortage of refrigerant
flowing through the coil.
3. Check that condensate from the evaporator and
economizer coils flows freely through the
condensate piping, traps, drain pan, and drainage
holes. Remove algae and or any airflow
obstructions.
M Ma aiin ntte en na an ncce e