Trane IntelliPak SAHL Series, Инструкция по установке, эксплуатации и обслуживанию

Страница: 10 / 201

10 RT-SVX36G-EN
Model Number Descriptions
DIGIT 14 - SUPPLY AIR FAN HP
1 = 3 HP 4 = 10 HP 7 = 25 HP
2 = 5 HP 5 = 15 HP 8 = 30 HP
3 = 7.5 HP 6 = 20 HP 9 = 40 HP
DIGIT 15 - SUPPLY AIR FAN
DRIVE
5 = 500 RPM B = 1100 RPM
6 = 600 RPM C = 1200 RPM
7 = 700 RPM D = 1300 RPM
8 = 800 RPM E = 1400 RPM
9 = 900 RPM F = 1500 RPM
A = 1000 RPM
DIGIT 16 - FRESH AIR
A = No Fresh Air
B = 0-25% Manual
D = 0-100%
Economizer
DIGIT 17 - SYSTEM CONTROL
1 = CV - Zone Temperature Control
2 = CV - Discharge Temperature Control
4 = CV - Zone Temperature Control
Space Pressure Control w/
Exhaust/Return VFD w/o Bypass
5 = CV - Zone Temperature Control
Space Pressure Control w/
Exhaust/Return VFD and Bypass
6 = VAV Discharge Temperature Control
w/ VFD w/o Bypass
7 = VAV Discharge Temperature Control
w/ VFD and Bypass
8 = VAV Discharge Temperature Control
Supply and Exhaust/Return Fan w/
VFD w/o Bypass
9 = VAV Discharge Temperature
Control Supply and Exhaust/Return
Fan with VFD and Bypass
A = VAV – Single Zone VAV – w/ VFD
w/o Bypass
B = VAV – Single Zone VAV – w/ VFD
w/ Bypass
C = VAV – Single Zone VAV – Supply and
Exhaust/Return Fan w/ VFD
w/o Bypass
D = VAV – Single Zone VAV – Supply and
Exhaust/Return Fan w/ VFD w/ Bypass
DIGIT 18 - ZONE SENSOR
0 = None
A = Dual Setpoint Manual or Auto
Changeover (BAYSENS108*)
B = Dual Setpoint Manual or Auto
Changeover w/ System Function
Lights (BAYSENS110*)
C = Room Sensor w/ Override and
Cancel Buttons (BAYSENS073*)
D = Room Sensor w/ Temperature
Adjustment and Override and
Cancel Buttons (BAYSENS074*)
L = Programmable Zone Sensor w/
System Function Lights for both
CV and VAV (BAYSENS119*)
Note: *Asterisk indicates current model
number digit A, B, C, etc. These
sensors can be ordered to ship
with the unit.
DIGIT 19 - AMBIENT CONTROL
0 = Standard
1 = 0° Fahrenheit
DIGIT 20 - AGENCY APPROVAL
0 = None (cULus Gas Heater, see note)
1 = cULus
Note: Includes cULus classified gas
heating section only when second
digit of Model No. is a "F."
DIGITS 21 - 38 -
MISCELLANEOUS
21 A = Unit Disconnect Switch
22 B = Hot Gas Bypass
C = Hot Gas Reheat w/out Hot Gas
Bypass
D = Hot Gas Reheat and Hot Gas
Bypass
23 0 = Without Economizer
C = Economizer Control w/
Comparative
Enthalpy
Z = Economizer Control w/
Reference Enthalpy
W = Economizer Control w/Dry Bulb
24 E = Low Leak Fresh Air Dampers
25 F = High Duct Temperature
Thermostat
26 G = High Capacity
27 * = Air-Cooled Aluminum
Condenser Coil
J = Corrosion Protected Condenser
Coil
A = Evap Condenser
B = Evap Condenser w/ Sump
Heater
C = Evap Condenser w/ Dolphin
WaterCare System
D = Evap Condenser w/ Sump
Heater and Dolphin WaterCare
System
E = Evap Condenser w/
Conductivity Controller
F = Evap Condenser w/
Conductivity Controller and
Sump Heater
Tip: EXAMPLE
Model numbers:
SAHL*5040A68A6BD800100W00
G0B000R000800 describes a unit
with the following characteristics:
DX Cooling Only unit w/ no
extended casing, 50 ton nominal
cooling capacity, 460/60/3 power
supply,100 percent exhaust with
Statitrac, 10 HP exhaust fan motor
with drive selection No. 8 (800
RPM), throwaway filters, 20 HP
supply fan motor with drive
selection No. B (1100 RPM), 0-
100% economizer w/ dry bulb
control, supply and exhaust VFD
w/o bypass, no remote panel,
standard ambient control, cULus
agency approval. High capacity
unit, extended grease lines and
spring isolators.
The service digit for each model
number contains 38 digits; all 38
digits must be referenced.
28 B = GBAS 0-10V
K = GBAS 0-5V
R = Rapid Restart
30 M = Remote Human Interface
31 N
= Ventilation Override Module
32 R = Extended Grease Lines
33 T = Access Doors
34 V = Inter-Processor
Communication Bridge
35 M = BACnet Communication
Interface (BCI) Module
Y = Trane Communication Interface
(TCI) Module
7 = Trane LonTalk Communication
Interface (LCI) Module
36 8 = Spring Isolators
37 6 = Factory-Powered 15A GFI
Convenience Outlet/Disconnect
Switch
38 J = Temperature Sensor