Trane HFCF-SVX01A-EN, Установка, эксплуатация и обслуживание

Страница: 15 / 16

When reassembling the fan housing, make
sure the fan wheel is balanced and centered in
the fan housing and not rubbing on either side.
Clean up debris on the fan wheel before start-
up.
Change Motor
The Fan Coil will not operate properly without
a functionally normal motor. If the motor fails,
order a replacement from the Trane
Company. The motor should be replaced by
completing the following steps:
1. Turn off the electrical power source and
then disconnect the motor wires. Allow
the rotating fan wheel to stop.
2. Disconnect the grounding wire on motor
shell.
3. For the motor with two fans, the fans must
be removed first before changing the motor.
Follow the "Change Fan Housing/Fan
Wheel" steps to remove one fan out of the
unit and motor shaft.
4. Loosen the bolt, on the other fan wheel,
from the motor shaft.
5. Loosen the screw and nut on two clamps
which hold the motor and motor seat
together, as shown on Figure 8-5 & 6.
6. Open the clamps and then remove the
clamps out of motor seats, as shown on
Figure 8-7. Hold the motor with one hand,
when removing the second clamp, to
prevent the motor from dropping off.
7. Follow the opposite procedures to reinstall
the new motor.
After replacing the motor, make sure the fan
wheel is balanced and centered in the fan
housing and not rubbing on either side.
Motor oil
Bearings are sealed for life and do not
require periodic lubrication.
Maintenance
Coil Reversing
1. Unscrew the bolt fixing the drain pan and
units.
2. Remove the drain pan.
3. Unscrew the bolt fixing the bottom plate
and units.
4. Remove the bottom plate.
5. Unscrew the bolt fixing the coil and units.
6. Rotate the coil for 180
° .
7. Reinstall the coil on the opposite
procedure.
Notes: The coil reversing should be completed
before hoisting.
Coil Cleaning
Clogged or dirty coil will reduce the cooling
capacity. Followings are the cleaning steps:
1. Disconnect the power and motor wire and
stop the fan.
2. Remove the whole fan seat and clean from
the air inlet.
3. Clean the coil fin using rigid nylon brush.
4. Clean it with dust collector.
5. Clean with high-pressure nozzle if there is
any compressed air.
6. Straighten the bended fin.
7. Connect the power again.
No need clean the coil if the filter is used and
periodically cleaned.
Drain Pan
The drain pan should be cleaned to allow
condensate flow. If it is clogged, steps
should be taken to clear the debris so that
condensate will flow out easily.
15
Control
Controls such as thermostats, control
valves, and motor speed switch may be
repaired locally; repair should be supervised
by the control manufacturer's representative.
Service Parts
The replacement parts are available through
the Trane Company or local Sales
Representative. When ordering parts, the
service part number and description must be
provided.
Maintenance Contract
It is strongly recommended that you sign a
maintenance contract with your local Trane
Service Agency.
This contact provides regular maintenance
of your installation by a specialist trained in
servicing Trane equipment.
Regular maintenance ensure that most
malfunctions are detected and corrected in
good time, and minimizes the possibility that
serious damage will occur. Regular
maintenance ensures the maximum
operating life and efficiency of your
equipment.
Training
The equipment described in this manual is
the result of many years of research and
continuous development. To assist you in
maintaining your equipment at peak
operating levels, Trane has operation training
available through the local Trane Sales Office.
This training could be provided at
nominal charge. The principle aim of this is to
give operators and maintenance technicians a
better knowledge of the equipment they are
using, or that is under their charge.
For further information, contact your nearest
Trane Sales Office.
HFCF-SVX01A-EN