background image

WSHP-SVX02A-EN

25

Preventive Maintenance

Maintenance on the unit is simplified 
with the following preventive sugges-
tions:

WARNING

Hazardous 

Voltage!

Disconnect all electric power, in-

cluding remote disconnects be-

fore servicing. Follow proper 

lockout/tagout procedures to en-

sure the power can not be inad-

vertently energized. Failure to 

disconnect power before servic-

ing could result in death or seri-

ous injury.

Check the contactors and relays within 
the control panel at least once a year. 
It is good practice to check the tight-
ness of the various wiring connections 
within the control panel.
A strainer (60 mesh or greater) must 
be used on an open loop system to 
keep debris from entering the unit heat 
exchanger and to ensure a clean sys-
tem.
For units on well water, it is important 
to check the cleanliness of the water-
to-refrigerant heat exchanger. Should 
it become contaminated with dirt and 
scaling as a result of bad water, the 
heat exchanger will have to be back 
flushed and cleaned with a chemical 
that will remove the scale. This service 
should be performed by an experi-
enced service person.

Maintenance

WARNING

Hazardous 

Chemicals!

Coil cleaning agents can be either 

acidic or highly alkaline. Handle 

chemical carefully. Proper han-

dling should include goggles or 

face shield, chemical resistant 

gloves, boots, apron or suit as re-

quired. For personal safety, refer 

to the cleaning agent manufactur-

ers Materials Safety Data Sheet 

and follow all recommended safe 

handling practices. Failure to fol-

low all safety instructions could 

result in death or serious injury.

It should be noted that the water qual-
ity should be checked periodically. See 
Table 9.

Table 9: Water Quality Table

Scaling

Calcium and magnesium 
(total hardness)

Less than 350 ppm

Corrosion

pH

7-9.5

Hydrogen Sulfide

Less than 1 ppm

Sulfates

Less than 25 ppm

Chlorides

Less than 125 ppm

Carbon Dioxide

Less than 75 ppm

Total dissolved solids 
(TDS)

Less than 1000 ppm

Biological Growth

Iron Bacteria

Low

Erosion

Suspended Solids

Low

Содержание EXWA
































Отзывы: