Trane CenTraVac CDHF, Руководство по сборке/разборке

Страница: 25 / 36

CVHE-SVN04M-EN 25
N NO OT TIIC CE E
E Eq qu uiip pm me en ntt D Da am ma ag ge e!!
P Prro op pe errlly y ssu up pp po orrtt tth he e cco om mp prre esssso orr cca assttiin ng g ffo oo ott tto o
a av vo oiid d p prre ev ve en ntt b brre ea akka ag ge e a an nd d e eq qu uiip pm me en ntt d da am ma ag ge e..
N No otte e:: Plan ahead where the compressor will be
secured. Build a suitable plant form to support
the assembly before the lift. Gently set
compressor onto prefabricated pre-formatted
support. Use care not to damage the cast
compressor foot (see foot in
Figure 8, p. 22 ).
Similarly, avoid damage to the discharge volute
flange (see discharge flange in
Figure 9, p. 22 ).
8. Remove the compressor/motor assembly. Remove
the locating dowel pins from the compressor foot
and discharge flange connections as shown in
Figure 8, p. 22 and Figure 9, p. 22 . To remove the
dowel pin, first remove the nut on the dowel pin,
place a bushing on the pin, and then reinstall the
nut. As the nut is tightened, the dowel pin should
pull out of its hole; at this point, remove the
compressor/motor assembly.
Compressor Motor Mount
Disassembly
If additional vertical clearance is required, the height of
the compressor motor mount can be reduced. Use the
following procedure:
1. Before cutting off the motor mount, first fabricate a
1/4-inch steel backing plate.
a. Cut the backing plate to shape and clamp it to
the motor mount.
b. Drill four 1/4-inch holes through the motor
mount and the backing plate as shown in Figure
16, p. 25 . These holes with bolts or roll pins
installed will be used to align the components
during reassembly.
c. Remove the backing plate.
2. Using an oxyacetylene torch, cut the mount as
shown in Figure 16, p. 25 .
During reassembly, use the backing plate with bolts or
roll pins to locate the pieces properly. After the pieces
are located, Trane recommends welding the mount and
backing plate in place.
Figure 16. Motor support detail
Cut Here
Compressor Motor
1/4-inch Steel
Alignment
Backing Plate
Bolt Holes
Economizer Removal
W WA AR RN NIIN NG G
R Re effrriig ge erra an ntt M Ma ay y B Be e U Un nd de err P Po ossiittiiv ve e
P Prre essssu urre e!!
F Fa aiillu urre e tto o ffo ollllo ow w iin nssttrru uccttiio on nss b be ello ow w cco ou ulld d rre essu ulltt iin n
a an n e ex xp pllo ossiio on n w wh hiicch h cco ou ulld d rre essu ulltt iin n d de ea atth h o orr
sse erriio ou uss iin njju urry y o orr e eq qu uiip pm me en ntt d da am ma ag ge e..
S Sy ysstte em m cco on ntta aiin nss rre effrriig ge erra an ntt a an nd d m ma ay y b be e u un nd de err
p po ossiittiiv ve e p prre essssu urre e;; ssy ysstte em m m ma ay y a allsso o cco on ntta aiin n o oiill..
R Re ecco ov ve err rre effrriig ge erra an ntt tto o rre elliie ev ve e p prre essssu urre e b be effo orre e
o op pe en niin ng g tth he e ssy ysstte em m.. S Se ee e u un niitt n na am me ep plla atte e ffo orr
rre effrriig ge erra an ntt tty yp pe e.. D Do o n no ott u usse e n no on n--a ap pp prro ov ve ed d
rre effrriig ge erra an nttss,, rre effrriig ge erra an ntt ssu ub bssttiittu utte ess,, o orr n no on n--
a ap pp prro ov ve ed d rre effrriig ge erra an ntt a ad dd diittiiv ve ess..
W WA AR RN NIIN NG G
H He ea av vy y O Ob bjje ecctt!!
F Fa aiillu urre e tto o ffo ollllo ow w iin nssttrru uccttiio on nss b be ello ow w cco ou ulld d rre essu ulltt iin n
u un niitt d drro op pp piin ng g w wh hiicch h cco ou ulld d rre essu ulltt iin n d de ea atth h o orr
sse erriio ou uss iin njju urry y,, a an nd d e eq qu uiip pm me en ntt o orr p prro op pe errtty y--o on nlly y
d da am ma ag ge e..
E En nssu urre e tth ha att a allll tth he e lliiffttiin ng g e eq qu uiip pm me en ntt u usse ed d iiss
p prro op pe errlly y rra atte ed d ffo orr tth he e w we eiig gh htt o off tth he e u un niitt b be eiin ng g
lliifftte ed d.. E Ea acch h o off tth he e cca ab blle ess ((cch ha aiin nss o orr sslliin ng gss)),, h ho oo okkss,,
a an nd d ssh ha acckklle ess u usse ed d tto o lliifftt tth he e u un niitt m mu usstt b be e cca ap pa ab blle e
o off ssu up pp po orrttiin ng g tth he e e en nttiirre e w we eiig gh htt o off tth he e u un niitt.. L Liiffttiin ng g
cca ab blle ess ((cch ha aiin nss o orr sslliin ng gss)) m ma ay y n no ott b be e o off tth he e ssa am me e
lle en ng gtth h.. A Ad djju usstt a ass n ne ecce essssa arry y ffo orr e ev ve en n u un niitt lliifftt..
1. Support the weight of the economizer with a
movable floor jack. Do not lift the economizer;
simply support it. Economizer weights are provided
in
Table 10, p. 18 ; also see submittal. It is
D Diissa asssse em mb blly y