manualshive.com logo in svg

Trane CeilAir CW, Инструкция по установке, эксплуатации и обслуживанию, Страница: 37 / 52

Поделиться
Скачать
Trane CeilAir CW Скачать руководство пользователя страница 37

Commissioning, Operation and Decommissioning

AH-SVX008C-EN

37 

Programming the Thermostat

A-Tech Controller

The A-Tech controller is a programmable thermostat that 
provides:

•

single- and dual-stage cooling control

•

on/auto/intermittent/off modes of operation

•

continuous/auto/residual fan

•

day/time clock

•

service reminders

•

language and °C/°F display preference

•

security features

•

temperature setpoint override

Note:

See the Robertshaw C9701i2 and C9725i2 User's 
Manual that accompanied your unit for 
programming instructions.

Microprocessor Controller

If the unit employs a controller, the controller was factory 
programmed based on the model of the A/C unit and the 
optional features selected. Most applications require no 
field start-up or program adjustment beyond setting the 
current date and time. Separate operating instructions for 
the controller have been sent with your unit, including 
each feature's factory "default" setting and the available 
adjustment range, if applicable.

Decommissioning the Unit

Personnel performing the decommissioning must be 
completely familiar with the unit before starting. Best 
practice requires all refrigerants be recovered safely. Prior 
to recovery, an oil and refrigerant sample should be taken 
in case analysis is required prior to re-use of the reclaimed 
refrigerant. Electrical power must be available before 
decommissioning is started.

Follow these decommissioning guidelines:

1. Become familiar with the equipment and its operation.

2. Isolate the system electrically.

3. Before attempting the procedure ensure that:

•

Mechanical handling equipment is available, if 
required, for handling refrigerant cylinders

•

All required personal protective equipment is 
available and used correctly

•

The recovery process is supervised at all times by 
competent personnel

•

Recovery equipment and cylinders conform to the 
appropriate standards

4. Pump down the refrigerant system, if possible.

5. If a vacuum is not possible, make a manifold so that 

refrigerant can be removed from various parts of the 
system.

6. Place the cylinder receiving the refrigerant on the scale 

before starting recovery.

7. Start the recovery machine and operate in accordance 

with manufacturer's instructions.

8. Do not overfill cylinders (They should contain no more 

than 80% volume liquid charge).

9. Do not exceed the maximum working pressure of the 

cylinder, even temporarily.

10. When the cylinders have been filled correctly and the 

process completed, make sure that the cylinders and 
the equipment are removed from site promptly and all 
isolation valves on the equipment are closed off.

11. Recovered refrigerant must not be charged into an- 

other refrigeration system unless it has been cleaned 
and checked.

Recovering Refrigerant

When removing refrigerant from a system, either for 
servicing or decommissioning, best practice is to remove 
all refrigerants safely. Use the following recommended 
guidelines:

•

When transferring refrigerant into cylinders, ensure 
that only appropriate refrigerant recovery cylinders 
are employed. Ensure that the correct number of 
cylinders for holding the total system charge are 
available and that all cylinders to be used are 
designated for the recovered refrigerant and labelled 
for that refrigerant (i.e., special cylinders for the 
recovery of refrigerant). Cylinders must be complete 
with pressure relief valve and associated shut-off 
valves in good working order. Empty recovery 
cylinders must be evacuated and, if possible, cooled 
before recovery occurs

•

Recovery equipment must be in good working order 
with a set of instructions concerning the equipment at 
hand, and the equipment must be suitable for 
recovering flammable refrigerants. In addition, a set of 
calibrated weighing scales must be available and in 
good working order. Hoses must be complete and in 
good condition with leak-free disconnect couplings. 
Before using the recovery machine, check that it is in 
satisfactory working order, has been properly 
maintained and that any associated electrical 
components are sealed to prevent ignition in theevent 
of a refrigerant release. Consult manufacturer ifin 
doubt.

•

Recovered refrigerant must be returned to the 
refrigerant supplier in the correct recovery cylinder, 
and the relevant Waste Transfer Note arranged. Do not 
mix refrigerants in recovery units and especially not in 
cylinders.

Содержание CeilAir CW





















































Отзывы:

Нет отзывов