Trane Axiom GWS Series, Инструкция по установке, эксплуатации и обслуживанию

Страница: 69 / 76

WSHP-SVX015C-EN 69
Troubleshooting
W WA AR RN NIIN NG G
H Ha azza arrd do ou uss S Se errv viicce e P Prro occe ed du urre ess!!
F Fa aiillu urre e tto o ffo ollllo ow w a allll p prre ecca au uttiio on nss iin n tth hiiss m ma an nu ua all a an nd d
o on n tth he e tta ag gss,, ssttiicckke errss,, a an nd d lla ab be ellss cco ou ulld d rre essu ulltt iin n
d de ea atth h o orr sse erriio ou uss iin njju urry y..
T Te ecch hn niicciia an nss,, iin n o orrd de err tto o p prro otte ecctt tth he em msse ellv ve ess ffrro om m
p po otte en nttiia all e elle eccttrriicca all,, m me ecch ha an niicca all,, a an nd d cch he em miicca all
h ha azza arrd dss,, M MU US ST T ffo ollllo ow w p prre ecca au uttiio on nss iin n tth hiiss m ma an nu ua all
a an nd d o on n tth he e tta ag gss,, ssttiicckke errss,, a an nd d lla ab be ellss,, a ass w we ellll a ass tth he e
ffo ollllo ow wiin ng g iin nssttrru uccttiio on nss:: U Un nlle essss ssp pe ecciiffiie ed d o otth he errw wiisse e,,
d diisscco on nn ne ecctt a allll e elle eccttrriicca all p po ow we err iin nccllu ud diin ng g rre em mo otte e
d diisscco on nn ne ecctt a an nd d d diisscch ha arrg ge e a allll e en ne errg gy y sstto orriin ng g
d de ev viicce ess ssu ucch h a ass cca ap pa acciitto orrss b be effo orre e sse errv viicciin ng g..
F Fo ollllo ow w p prro op pe err llo occkko ou utt//tta ag go ou utt p prro occe ed du urre ess tto o
e en nssu urre e tth he e p po ow we err cca an n n no ott b be e iin na ad dv ve errtte en nttlly y
e en ne errg giizze ed d.. W Wh he en n n ne ecce essssa arry y tto o w wo orrkk w wiitth h lliiv ve e
e elle eccttrriicca all cco om mp po on ne en nttss,, h ha av ve e a a q qu ua alliiffiie ed d lliicce en nsse ed d
e elle eccttrriicciia an n o orr o otth he err iin nd diiv viid du ua all w wh ho o h ha ass b be ee en n
ttrra aiin ne ed d iin n h ha an nd dlliin ng g lliiv ve e e elle eccttrriicca all cco om mp po on ne en nttss
p pe errffo orrm m tth he esse e tta asskkss..
ReliaTel ™ ™ Controls
The RTRM has the ability to provide the service
personnel with some unit diagnostics and system
status information.
Before turning the main power disconnect switch
“Off”, follow the steps below to check the ReliaTel
™
Refrigeration Module (RTRM). All diagnostics & system
status information stored in the RTRM will be lost when
the main power is turned “Off”.
To prevent injury or death from electrocution, it is the
responsibility of the technician to recognize this hazard
and use extreme care when performing service
procedures with the electrical power energized.
1. Verify that the Liteport LED on the RTRM is burning
continuously. If the LED is lit, go to Step 3.
2. If the LED is not lit, verify that 24 VAC is presence
between J1-1 and J1-2. If 24 Vac is present, proceed
to Step 3. If 24 Vac is not present, check the unit
main power supply, check transformer (TNS1).
Proceed to Step 3 if necessary.
3. Utilizing “Method 1” or “Method 2” in the “System
Status Checkout Procedure ” section, check the
following:
System status
Heating status
Cooling status
If a System failure is indicated, proceed to Step 4. If
no failures are indicated, proceed to Step 5.
4. If a System failure is indicated, recheck Steps 1 and
2. If the LED is not lit in Step 1, and 24 VAC is
present in Step 2, the RTRM has failed. Replace the
RTRM.
5. If no failures are indicated, use one of the TEST
mode procedures described in the “Unit Start-Up”
section to start the unit. This procedure will allow
you to check all of the RTRM outputs, and all of the
external controls (relays, contactors, etc.) that the
RTRM outputs energize, for each respective mode.
Proceed to Step 6.
6. Step the system through all of the available modes,
and verify operation of all outputs, controls, and
modes. If a problem in operation is noted in any
mode, you may leave the system in that mode for
up to one hour while troubleshooting. Refer to the
sequence of operations for each mode, to assist in
verifying proper operation. Make the necessary
repairs and proceed to Steps 7 and 8.
7. If no abnormal operating conditions appear in the
test mode, exit the test mode by turning the power
“Off” at the main power disconnect switch.
8. Refer to the individual component test procedures if
other microelectronic components are suspect.
System Status Checkout
Procedure
“System Status” is checked by using one of the
following two methods:
Method 1
If the Zone Sensor Module (ZSM) is equipped with a
remote panel with LED status indication, you can check
the unit within the space. If the ZSM does not have
LED’s, use Method 2. BAYSENS110*, and
BAYSENS119* all have the remote panel indication
feature. The LED descriptions are listed below.
LED 1 (System)
“On” during normal operation.
“Off” if a system failure occurs or the LED fails.
“Flashing” indicates test mode.
LED 2 (Heat)
“On” when the heat cycle is operating.
“Off” when the heat cycle terminates or the LED fails.
“Flashing” indicates a heating failure.
LED 3 (Cool)
“On” when the cooling cycle is operating.
“Off” when the cooling cycle terminates or the LED
fails.
“Flashing” indicates a cooling failure.