background image

Figure 14. Bracket removal for deluxe sound package

Installation

18

 WSHP-SVX10H-EN

4. Connect water coil pipe to the system riser with a flexible 

steel hose assembly. 

5. Verify that the shut-off/balancing valve in the return line/

supply line are closed.

6. Place shut-off valves in appropriate location (see sticker on 

the equipment for best placement recommendation) to 
allow chassis to slide easily in/out of unit cabinet.

7. Flush the system using the cleaning and flushing the water 

loop instructions.

8. Open the unit water valves and check piping for leaks.
9. Connect electrical to unit chassis via the quick connect 

mating plugs.

Note:

Four plugs are included (motor, optional condensate 
overflow, power and thermostat).

10. Slide chassis into the cabinet. Center the chassis left to 

right to minimize sound transmission.

Figure 15. Install chassis centered

11. Verify unit’s air filter has shipped with the cabinet. 
12. Install cabinet’s front cover to the hinged door.

Important:

Ensure the gasket material creates a positive 
seal around the entire coil to avoid coil bypass. 
If a field supplied door is used, ensure the front 
cover is attached to the building structure and 
not the unit cabinet.

Supply Grille Installation

Table 7.

Supply air opening size

GET

Single Grille 

100% CFM 

(inches)

Two Grille 

50% CFM 

(inches)

Three Grille 

33% CFM

(inches)

Top 

Discharge 

up to 100% 

CFM

(inches)

009-012

14 W x 14 H

10 W x 6 H

Not 

Recommended

14 W x 10 H

015-018

16 Wx12 H

14 Wx12 H

12 Wx8 H

16 Wx14 H

024

22 Wx18 H

14 Wx12 H

12 Wx8 H

16 Wx14 H

036

Not 

Recommended

16 Wx14 H

14 Wx12 H

17 Wx17 H

1. Install the supply grille(s) into the cabinet discharge 

opening. Ensure there are no air gaps between the cabinet 
supply air and the grille. This helps prevent recirculation of 
supply air into the return air opening behind the drywall.

2. Secure grille(s) into the drywall via two screws.

Cleaning and Flushing the Water Loop

After the piping system is complete, the flexible hose 
connectors should be doubled back to complete the water 
circuit external to the unit (avoiding trash settle-out in the 
condenser). An extra pipe may be necessary to connect the 
hose kits. See 

“Using Antifreeze,” p. 19

 for antifreeze/water 

mixture by volume.
1. Water circulation system should be filled with clean water 

using the water make up connections.

Note:

Air vents should be opened during filling.

2. With the air vents closed, start the circulating pump and 

then crack the air vents to bleed off the trapped air, 
assuring circulation through all components of the system.

Notes:

Make up water must be available to the system to replace 
the volume formerly occupied by the air that is bled off.

System water pressure needs to be relieved prior to 
opening system.

3. With the air vented and the water circulating, the entire 

system should be checked for leaks with repairs made as 
required.

4. Operate the supplementary heat system making checks 

per manufacturer’s instructions. During this operation, 
visual checks should be made for leaks that may have 
occurred due to increased heat. Repair as required.

5. Open the system at the lowest point for the initial blow 

down (making sure the make up water is equal to the water 
being dumped). Continue blow down until the water 
leaving the drain runs clear, but not less than 2 hours.

6. Shut down pumps and supplementary heat system. 

Reconnect the hoses placing the water-to-refrigerant heat 
exchanger in the water circulating system.

Содержание Axiom GET024-036









































Отзывы: