background image

 

                                                                 

  Page 9

Installer’s Guide

3

/

4

" PVC OR COPPER

TUBING AND FITTINGS

QTY.

1
3
1
1
2
1

MATERIALS

TEE
90˚ ELL
PLUG
4" NIPPLE
2" NIPPLE
3/4" NPT TO PVC OR

COPPER ADAPTER

2" 

MIN.

2" 

MIN.

FROM DWG. 21C128186 FIG 1, R1

Condensate Drain Piping

A 3/4-inch female NPT condensate drain connection is provided on the evapo-
rator access panel end of the unit. Provide a trap and fill it with water before 
starting the unit to avoid air from being drawn through. Follow local codes and 
standard piping practices when running the drain line. Pitch the line downward 
away from the unit. Avoid long horizontal runs. See Figure 5, below.

NOTE:  Do not use reducing fittings in the drain lines

 
The condensate drain must be:

  

Made of 3/4" pipe size.

  

Pitched 1/4" per foot to provide free drainage to conve 

 

nient drain system.

  

Trapped.

  

Must not be connected to a closed drain system unless  

 

the trap is properly vented.

Figure 5.  Typical Condensate Drain Piping

Table 1. Determine Filter Size

*Filters must be installed in the return air system.  The above square footages 
are based on 300 F.P.M. face velocity.  If permanent filters are used, size per 
mfg. Recommendation with clear resistance of 0.05"WC.

UNIT

NOMINAL

CFM

FILTER*

(Sq Ft) SIZE

FILTER

RESISTANCE

4WHC3024A

800

2.67

0.05

4WHC3030A

1000

3.33

0.05

4WHC3036A

1200

4.00

0.05

4WHC3042A

1400

4.67

0.05

4WHC3048A

1600

5.33

0.05

4WHC3060A

2000

6.67

0.05

Air Filters

These units require filters with adequate filter area be provided in the return air 
duct.  Table 2 below gives filter data.  The specific location of the filters depends 
on the type of installation and the layout of the duct system.  Be sure the owner 
is aware of the location of the filter and the need to change them as required.  
The Filter Size (Sq. Ft.) are based on 300 F.P.M. face velocity. If permanent 
filters are used, size per mfg. recommendation with clean resistance of .05" WC. 

Содержание 4WHC3024





















Отзывы: