Trane Technologies CVHE Скачать руководство пользователя страница 3

Страница: 3 / 95

WARNING

Contains Refrigerant!

System contains oil and refrigerant under high pres-

sure. Recover refrigerant to relieve pressure before

opening the system. See unit nameplate for refrigerant

type. Do not use non-approved refrigerants, refrigerant

substitutes, or refrigerant additives.

Failure to follow proper procedures or the use of

non-approved refrigerants, refrigerant substitutes, or

refrigerant additives could result in death or serious

injury or equipment damage.

WARNING

Personal Protective Equipment (PPE)

Required!

Installing/servicing this unit could result in exposure

to electrical, mechanical and chemical hazards.

• Before installing/servicing this unit, technicians

MUST put on all Personal Protective Equipment

(PPE) recommended for the work being undertak-

en. (Examples; cut resistant gloves/sleeves, butyl

gloves, safety glasses, hard hat/bump cap, fall

protection, electrical PPE and arc flash clothing).

ALWAYS refer to appropriate MSDS sheets and

OSHA guidelines for proper PPE.

• When working with or around hazardous chem-

icals, ALWAYS refer to the appropriate MSDS

sheets and OSHA guidelines for information on

allowable personal exposure levels, proper respira-

tory protection and handling recommendations.

• If there is a risk of arc or flash, technicians MUST

put on all necessary Personal Protective Equipment

(PPE) in accordance with NFPA70E for arc/flash

protection PRIOR to servicing the unit.

• NEVER PERFORM ANY SWITCHING, DISCONNECT-

ING, OR VOLTAGE TESTING WITHOUT PROPER

ELECTRICAL PPE AND ARC FLASH CLOTHING.

ENSURE ELECTRICAL

• METERS AND EQUIPMENT ARE PROPERLY RATED
• FOR INTENDED VOLTAGE.

Failure to follow recommendations could result in

death or serious injury.

Trademarks

Trane and the Trane logo are trademarks of Trane in the
United States and other countries. All trademarks ref-
erenced in this document are the trademarks of their
respective owners.

TCVHE-SVX04D-EN 3

RELEASED 10/Mar/2020 06:59:20 GMT

Содержание CVHE
































































































Результаты поиска

Содержание CVHE

Отзывы:

Похожие инструкции для CVHE

Бренды по названию

Популярные бренды

Trane Technologies CVHE, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание CVHE

Отзывы:

Похожие инструкции для CVHE

Бренды по названию

Популярные бренды