background image

                

www.TrailFX.com

 

 

Page 

9

 of 

9                                                                                                                                                                                    

Rev 010115 

 

1.

Hardware’s are not of correct size. 

In  GMC /  Chevrolet  truck  model 2006  &  up, customer  needs  to  reuse  the factory  body  bolts to  install  the  bracket.  If your  vehicle is not 

GMC  /  Chevrolet  2006  &  up,  ensure  that  holes  are  not  partially  covered  with  any  plastic  grommet  or  rust?    If  it  is,  remove  the  plastic 

grommet & rust from the thread holes & re-try the installation. 

2.

Mounting Bracket are not getting Installed properly.  

In some cases Illustration images shown in Installation manual may not be the exactly same as per actual vehicle images ,also if Driver / 

Passenger side mounting brackets are very identical in the design, suggest referring Parts Identification guide to avoid fitment issue. 

3.

Products are thumping / rattling after installation. 

E

nsure  that  all  required  mounting  brackets  /  hardware’s  are  installed  &  tighten  correctly.  Suggest  using  white  lithium  /  regular  grease 

between the metal to metal contact surfaces. 

4.

Side Bar is not aligning with vehicle / Step Pads are not aligning with vehicle doors. 

Side bar may be interchanged or mounting brackets are not installed at the correct position in the vehicle. Refer Parts identification guide. 

5.

Missing / Excess Hardware. 

Recheck hardware count as per the part list. 

6.

Product not installing properly.  

Ensure make model year, cab length and bed size of your vehicle is listed in the application. All installation steps are followed correctly.

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Check out these other TrailFX Products!!

                                                                                                         

www.TrailFX.com

 

 
 
 
 
 
 
 
 

Periodically check the product to ensure all fasteners are tight and components are intact. 

Regular waxing is recommended to protect the finish of the product. 

Use ONLY Non-Abrasive automotive wax.

 Use of any soap, polish or wax that contains an abrasive is detrimental and can scratch the 

finish leading to corrosion. 

Aluminum polish may be used to polish small scratches and scuffs for 

Stainless Steel finish.

 

Mild soap may be used to clean the product for both 

Stainless Steel and Black finish.

 

Keystone Automotive Operations Inc. (KAO) warrants this product to be free of defects in material and workmanship at the time of purchase by the 
original retail consumer. KAO disclaims any other warranties, express or implied, including the warranty of fitness for a particular purpose or an 
intended use. If the product is found to be defective, KAO may replace or repair the product at our option, when the product  is returned prepaid, 
with  proof  of  purchase.  Alteration  to,  improper  installation,  or  misuse  of  this  product  voids 

the  warranty.  KAO’s  liability  is  limited  to  repair  or 

replacement of products found to be defective, and specifically excludes liability for any incidental or consequential loss or damage.

 

 

Содержание R0004RB










Отзывы: