www.TrailFX.com
Page
2
of
7
Rev R00; 101519
PROCEDURE:
1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS
CAREFULLY BEFORE STARTING INSTALLATION. SIDE STEPS OR RUNNING BOARDS MUST
BE REMOVED BEFORE INSTALLATION.
2.
Start installation on the Passenger/Right front of the vehicle. Find the front threaded insert located in
between the first pair of holes along the pinch weld,
(Figure 2)
. Installation will use the 1st, 2nd and 4th
mounting locations,
(Figure 1)
.
3.
Select the Passenger/Right Front Mounting Bracket,
(Figure 3)
.
IMPORTANT
: Use the illustration
above and
Figure 3
to properly identify the Mounting Bracket. Attach the Mounting Bracket to the
threaded insert using (1) 8mm x 35mm Hex Bolt, (1) 8mm Lock Washer and (1) 8mm Flat Washer,
(Figures 4 & 5)
. Do not tighten hardware.
4.
Select the Passenger/Right Front Support Bracket.
IMPORTANT
: Use the illustration above to help
identify the correct Support Bracket. Attach the Support Bracket to the pinch weld using (2) 6mm Hex
Bolts, (4) 6 mm Flat Washers and (2) 6mm Nylon Lock Nuts,
(Figure 6)
.
NOTE:
Insert bolts from the
outside of the pinch weld and through the Bracket.
Attach the Support Bracket to the Mounting
Bracket with (1) 10mm Hex Bolt, (2) 10mm Flat Washers and (1) 10mm Nylon Lock Nut,
(Figures 7 &
8)
. Do not tighten hardware.
5.
Move to the 2nd mounting location and locate the threaded insert and pair of holes in the pinch weld,
(Figure 9)
. Repeat
Steps 3 & 4
to install the Passenger/Right Center Mounting and Support Brackets,
(Figures 3, 10
—12)
.
NOTE:
The Center and Rear Mounting Brackets look similar but each one is
unique. The Center Support Bracket has a hole in the top and a notch on the bottom. The Rear Support
Bracket has a notch at the top,
(Figure 11)
. Do not tighten hardware.
6.
Move to the last mounting location on the rocker panel and locate the threaded insert and pair of holes
in the pinch weld,
(Figure 13)
. Repeat
Steps 3 & 4
to install the Passenger/Right Rear Mounting and
Support Brackets,
(Figures 3, 11 & 14)
. Do not tighten hardware.
7.
Select the Passenger/Right Sidebar. Use the illustration above to select the correct Sidebar. Carefully
position the Sidebar onto the (3) Mounting Brackets.
IMPORTANT
: Do not slide, (front to back or
rotate), the Sidebar on the Brackets or damage to the finish on the Sidebar may result. Attach the
Sidebar to the Mounting Brackets with (6) 8mm x 25mm Combo Bolts,
(Figure 15)
. Do not tighten
hardware.
8.
Level and adjust the Sidebar and tighten all hardware.
Passenger/Right Center
Mounting Bracket
Passenger/Right
Front Support
Bracket
Driver/Left Center
Mounting Bracket
Driver/Left Center
Support Bracket
Passenger/Right
Rear
Support Bracket
Passenger/Right
Front Mounting
Bracket
Driver/Left Front
Mounting Bracket
Driver/Left
Front Support
Bracket
Driver/Left Rear
Support Bracket
Passenger/Right
Sidebar
Front
Passenger/Right
Rear Mounting
Bracket
Driver/Left
Rear
Mounting
Bracket
Passenger/Right
Center
Support Bracket
NOTE: The Center threaded
inserts are closer to the front
