manualshive.com logo in svg

Trafox SUPERINTEND IM-04DCCT, Инструкция по установке и эксплуатации

Поделиться
Скачать
Trafox SUPERINTEND IM-04DCCT Скачать руководство пользователя страница 16

16

 

© Copyright Muuntosähkö Oy 

–

 Trafox

 

Superintend IMD 

 

http://www.trafox.fi

 

•

 

START-UP DELAY:

 The delay after powering on the unit during which the alarms 

will not be generated. 

The setup range is 0…60 s.

 

•

 

MODBUS ADDRESS: 

The Modbus slave address of the unit. The setup range is 

1…247.

 

•

 

FACTORY SETTINGS: 

Returns all settings to their original values.

 

 

ERRORS 

 

The following table lists the functioning of the IM-04DCCT unit in various error situations. 

 

Error

 

IM

-

04DCCT 

 

ALARM 
LEDs

 

IM

-

04DCCT

 

ALARM 
menu

 

Alarm 
relay

 

The IM

-

04DCCT unit 

without operating voltage

 

 

 

ALM WRN

 

Insulation fault (R under 

InsLimit)

 

ALARM

 

Insulat.

 

ALM

 

Insulation fault (R under 

PrInsLim)

 

WARN

 

PreInsul

 

WRN

 

The IM

-

04DCCT unit TG 

wire is disconnected

 

STATUS ALARM

 

Gnd Fail

 

ALM

 

The IM

-

04DCCT unit MG 

wire is disconnected

 

STATUS ALARM

 

Gnd Fail

 

ALM

 

System fault (manual 

test)

 

STATUS ALARM

 

Sys Test

 

ALM

 

 

Alarm relays:

 

•

 

ALM insulation alarm

 

•

 

WRN insulation pre

-

alarm

 

Error situations are displayed by means of ALARM LEDs and the alarm menu of the IM

-

04DCCT unit. A blinking LED always means that an alarm is active, and a steady 
indicator indicates a fixed and unacknowledged fault.

 

 

MODBUS RTU REMOTE CONTROL 

 

When a suitable Modbus address has been set for the IM-04DCCT unit, the device can be 
connected to a RS-485 bus. The unit's Modbus RTU slave functionality is now ready for 

use. The unit’s Modbus

 RTU register map is provided below. The Modbus functions to be 

used are Read Holding Registers (0x03) and Write Multiple Registers (0x10). 

 

 

Содержание SUPERINTEND IM-04DCCT





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды