manualshive.com logo in svg

Trafox SUPERINTEND IM-04DCCT, Инструкция по установке и эксплуатации

Поделиться
Скачать
Trafox SUPERINTEND IM-04DCCT Скачать руководство пользователя страница 14

14

 

© Copyright Muuntosähkö Oy 

–

 Trafox

 

Superintend IMD 

 

http://www.trafox.fi

 

 

The insulation fault alarm has been deactivated but not 
acknowledged. 
The smallest insulation resistance measured during the fault, the 
alarm limit's set value and the fault start time are displayed. 

 

 

The 

Insulat. 

and

 PreInsul 

alarms are active if the measured insulation resistance is 

smaller than the alarm or pre-alarm limit. 

 

The 

Sys Test

 alarm is active if the manual system test fails. In that case, the insulation 

resistance can not be measured either, so an insulation resistance alarm is also given.

 

The 

Gnd Fail 

alarm is active if the TG or MG wire of the IM-04DCCT unit is disconnected. 

In that case, the insulation resistance can not be measured either, so an insulation 
resistance alarm is also given. 

 

SETUP MENU 

 

The Setup menu can be used to change system settings, alarm limits, time etc. 

The Setup menu is password-protected and accessed as follows:  

•

 

Go to the Setup menu in the main menu. The screen displays “Enter Setup”. 

Press T. 

•

 

Change the blinking number with the   button and press the   button to move 
to the next digit. Enter the three digits and press T. After this, you can navigate 
the menu with the   button. 

•

 

The   button takes you to the initial mode. 

The password is “123”.

 

All information on the settings of the device alarm limits and the system are saved in the 
internal EEPROM memory of the IM-04DCCT unit. 

 

 

 

 

 

Содержание SUPERINTEND IM-04DCCT





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды