03/20
Product Code: 1054T
Made in China to TQB Brands Pty Ltd specifications
Page 4
Visit us at www.tqbbrands.com.au
About the TradeQuip brand
The 'TradeQuip' brand of workshop equipment, is designed for use in a demanding workshop
environment
by
professional users. With
proven
and
trusted “
Made for the
Trade”
reliability,
'TradeQuip'
branded products offer the very best in performance for an
affordable price. All backed by a 1year trade guarantee across 1,000+ distributors Australia wide.
ASSEMBLY, OPERATION, PREVENTITIVE MAINTENANCE
1.
FEATURES & MODELS
The
TradeQuip "Made for the Trade"
Vehicle Positioning Jacks manoeuvre vehicles safely and easily, without touching the
chassis! Constructed from high-quality powder-coated steel, they have a lifting capacity of 680kg each. The smooth foot
operated support legs lift the tyre off the ground, and the locking pin ensures optimum safety. Heavy-duty swivel castor
wheels enable the rolling of cars, quad bikes, vans and light trucks into tight areas with ease. Relocating non-running vehicles
or shells will never again be a drama! This pair of positioning jacks will allow 180ᵒ pivoting, add you can add an extra pair to
allow for 360ᵒ manoeuvrability.
2.
ASSEMBLY
Unpacking: after removing the packing material, make sure the product is in perfect condition and that there are no visible
damaged parts.
Refer to the Parts List on page 6 for contents
1.
Index numbers 2, 4 and 5 represent the base leg assemblies.
2.
Secure the base leg assemblies to the inner tube #6 and outer tube#29 with the washers #28, lock washers #27 and
bolts #26 provided as shown in the exploded view drawing on page 6.
3.
Secure the castor wheels with brakes #11 to the inner tube #6 and outer tube #29 by tightening the nuts #1.
4.
Secure the castor wheels #3 to the ends of the base leg assemblies with the nuts #1.
5.
Securing the pedal assembly #12 when the dolly is stored or not in use can be accomplished by rotating the latch #15
toward the pedal end of the pedal assembly #12 and rotating the lock pin #9 upward so that it enters the rectangular
hole in the top of the pedal assembly #12.
3.
BEFORE USE
Prior to each use conduct a visual inspection checking for abnormal conditions, such as cracked welds, leaks, and damaged,
loose, or missing parts.
1.
Lubricate the slides and castors
2.
Clean all parts and surfaces
3.
Maintain all operating and warning labels
4.
OPERATION
1.
Ensure the vehicle is on a hard, flat, dry surface and the transmission is in PARK or engaged in gear if a manual
transmission before using these Vehicle Positioning Jacks.
2.
Release the pedal assembly #12 from the outer tube #29 by pushing down on the pedal end of the assembly with
one hand and rotating the latch #9 out of the rectangular hole in the top of the pedal assembly #12 with the other
hand.
3.
Spread the base leg assemblies far enough apart where they will straddle the vehicle tyre.
4.
Push the jack in toward the tyre where the rollers of the base leg assemblies are straddling the tyre and the centre
of the tyre is in line with the centre of each roller.
5.
Rotate the latch #15 in the opposite direction so the front claw #13 engages the teeth in the inner tube #6.
6.
Activate the pedal assembly #12 so the rollers make contact with the circumference of the tyre. Again, make sure
the tyre is properly aligned with the rollers. Continue activating the pedal assembly until the tyre is lifted 25mm off
the ground.
7.
Repeat steps 1 through 6 on the remaining three tyres. Check to see if the 25mm clearance will be enough to
manoeuvre the vehicle over the floor without any obstructions. It may be necessary to increase the 1’ ground
clearance.
8.
Once the vehicle is supported by the dollies, move the vehicle slowly and carefully to its destination and engage
the locking caster wheels on all four dollies.
9.
Removing the vehicle from the dolly will require disengaging the caster locks.
10.
Rotate the #15 latch forward towards the foot pedal and then continue to activate the foot pedal until the rollers of
the base leg assemblies clear the circumference of the tire. Remove the dolly from under the vehicle
11.
When work is done, check under the lift to ensure that there are no obstructions and that it is safe to lower the unit.
