manualshive.com logo in svg

Tracmaster Camon SG30, Оригинальное руководство пользователя

Поделиться
Скачать
Tracmaster Camon SG30 Скачать руководство пользователя страница 17

CAMON SG30 Stump Grinder

SG30 Stump Grinder

 

Page 15

Helpful tips for operating the Stump Grinder

Use smooth, comfortable movements while operating.
When it is desired to cut smaller roots, it may be more effective to do so before, 

rather than after, cutting the stump.
Should the chip build-up become excessive when cutting, shut off the machine, 

wait for the cutting wheel to stop rotating, retract the machine from the stump, 

and rake away chips.
On larger stumps, when cutting from one side, eventually a tyre may tend to roll 

into the hole. This may be prevented by moving the machine to another side of the 

stump to continue removal, or by filling the hole with chips before continuing.

WARNING: NEVER USE THE STUMP GRINDER IN POOR LIGHT OR AT NIGHT.

6.7 

Procedure for Unexpected Shut Down

Release the Operator Presence Control (OPC) lever.
Push down on the handlebars to raise the teeth into the air.
Ensure  the  rotor  shaft  and  blades  have  stopped  rotating  prior  to  moving  the 

machine.

6.8  Residual Risks of the SG30 Stump Grinder

The rotor shaft will continue to rotate for several seconds once the operating lever 

has been released. Ensure that the blades have stopped rotating prior to moving or 

tilting the machine.
The SG30 Stump Grinder is designed to be pushed by the operator both during 

transportation and operation. The SG30 is fitted with a wheel brake on the left hand 

wheel that may be used to hold the machine on sloped areas.

 

!

Содержание Camon SG30





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды