Trackmaster TMX428 Скачать руководство пользователя страница 91

Страница: 91 / 159

TRACKMASTER

Ch. 9

Troubleshooting

317-160-406 Rev 4

TMX428 TMX428CP & TMX58 Service Manual

May 2021

Control Console Communication Flow Chart 1S

Do you see the Welcome

screen?

Yes

Treadmill should

be operational.

Verify the harness between LCD Screen J8 connector
and Smart Power Supply FG0495 J12 connector is
properly connected. Inspect cable to see if damaged or
loose connector.

LCD Screen FG0496 (3

Edition)

LCD Screen FG0698 (4

Edition)

Did the Welcome

screen appear?

Yes

Is the screen displaying

ESTABLISHING

COMMUNICATION?

Verify the Emergency Stop Button is released.

Treadmill should

be operational.

Replace LCD Screen
417-160-017

Turn the treadmill power switch OFF (O).

Turn the treadmill power switch ON (-).

Yes

Replace Communication
Cable 317-160-264

Is the RS232 or

USB Interface

cable damaged?

Did the Welcome

screen appear?

Yes

Treadmill should

be operational.

Replace Smart
Power Supply
317-160-199

Yes

Содержание TMX428
































































































































































Результаты поиска

Содержание TMX428

Отзывы:

Бренды по названию

Популярные бренды

Trackmaster TMX428, Руководство по обслуживанию

Результаты поиска

Содержание TMX428

Отзывы:

Бренды по названию

Популярные бренды