Trackmaster TMX428 Скачать руководство пользователя страница 87

Страница: 87 / 159

TRACKMASTER

Ch. 9

Troubleshooting

317-160-406 Rev 4

TMX428 TMX428CP & TMX58 Service Manual

May 2021

Smart Power

Supply Error Code 7 Flow Chart 1P “Excessive Speed Mismatch”

Is the Red LED D13

flashing 7 times with

4 second pause on the

Smart Power Supply

FG0495?

Yes

Turn the treadmill power
switch OFF (O).

Is the Red LED D13

flashing on the

Smart Power Supply

FG0495?

Yes

Treadmill should

be operational.

Verify the harness between Drive PC2303-012-N
and Smart Power Supply FG0495 is properly
connected and not damaged.

Was the harness

damaged?

Was the harness

properly

connected?

Replace Harness
317-160-208

Yes

Connect harness.

Verify the harness between Motor
PMC5FA-00101-03 and Drive PC2303-012-N
is properly connected and not damaged.

Yes

Was the harness

damaged?

Was the harness

properly

connected?

Replace Motor
317-160-197

Yes

Connect harness.

Yes

Turn the treadmill power switch
OFF (O) for 10 seconds then
turn the power switch ON (-).

Is the Red LED D13

on the Smart Power

Supply FG0495 on

continuously?

Yes

Содержание TMX428
































































































































































Результаты поиска

Содержание TMX428

Отзывы:

Бренды по названию

Популярные бренды

Trackmaster TMX428, Руководство по обслуживанию

Результаты поиска

Содержание TMX428

Отзывы:

Бренды по названию

Популярные бренды