Trackmaster TMX428 страница 86 Скачать руководство пользователя

Страница: 86 / 159

Troubleshooting

Ch. 9

TRACKMASTER

TMX428 TMX428CP & TMX58 Service Manual

317-160-406 Rev 4

May 2021

Smart Power

Supply Error Code 6 Flow Chart 1O “Over Speed Base On External Speed

Sensor”

Is the Red LED D13

flashing 6 times with

4 second pause on the

Smart Power Supply

FG0495?

Yes

Turn the treadmill power switch
OFF (O) for 10 seconds then
turn the power switch ON (-).

Is the Red LED D13

on the Smart Power

Supply FG0495 on

continuously?

Yes

Is the Red LED D13

flashing on the

Smart Power Supply

FG0495?

Yes

Treadmill should

be operational.

Verify that the speed sensor gap to flywheel

magnet is 1/4” and connector is secure on J10

on the Smart Power Supply FG0495.

Verify when the fly wheel magnet passes by the
speed sensor that D10 LED on the Smart Power
Supply FG0495 the red led light is on then goes
out after the speed is not present.

Send a Start Belt Command or Press
Start if equipped with controller.
Speed the treadmill up to 10 MPH

With the treadmill

running at 10.0

MPH for 1 minute,

is the Red LED

D13 on?

Replace Speed Sensor
317-160-305

Yes

Treadmill should

be operational.

Yes

Is the Red LED D13

flashing 6 times with

4 second pause on the

Smart Power Supply

FG0495

Is the Red LED D10 on

the Smart Power Supply

FG0495 flashing ON &

Off when passing by

flywheel magnet?

Yes

Replace Smart Power Supply
317-160-199

Содержание TMX428
































































































































































Результаты поиска

Содержание TMX428

Отзывы:

Похожие инструкции для TMX428

Бренды по названию

Популярные бренды

Trackmaster TMX428, Руководство по обслуживанию

Результаты поиска

Содержание TMX428

Отзывы:

Похожие инструкции для TMX428

Бренды по названию

Популярные бренды