Trackmaster TMX428 страница 82 Скачать руководство пользователя

Страница: 82 / 159

Troubleshooting

Ch. 9

TRACKMASTER

TMX428 TMX428CP & TMX58 Service Manual

317-160-406 Rev 4

May 2021

Smart Power

Supply Error Code 2 Flow Chart 1K “Elevation Error”

Is the Red LED D13

flashing 2 times with

4 second pause on the

Smart Power Supply

FG0495?

Yes

Turn the treadmill power switch
OFF (O) for 10 seconds then
turn the power switch ON (-).

Did the Red LED

D9 light Up

momentarily?

Yes

Remove the black cap from actuator; & verify wires
are not disconnected to the reed switch or limit
switch.

Is the Red LED D13

flashing on the

Smart Power Supply

FG0495?

Yes

Treadmill should

be operational.

Verify Elevation Voltage JP1

Turn the treadmill power switch
OFF (O).

Did the Volt

meter

momentarily read

incoming voltage?

Yes

Verify Elevation Voltage JP1
between Incline Down Red &
Incline Common White.

Turn the treadmill power switch
ON (-).

Replace Smart Power
Supply FG0495.

Turn the treadmill power switch
OFF (O).

Perform Test Plug Procedure
to test elevation & treadmill
running belt speed.

Did treadmill

cycle according to

Test Plug

Procedure?

Yes

Replace Elevation
Actuator.

Connect Stress System &
perform test.

Did treadmill

respond to

Test

Procedure?

Yes

Return Treadmill

to service.

Replace Elevation
Actuator.

Smart

Power

Содержание TMX428
































































































































































Результаты поиска

Содержание TMX428

Отзывы:

Похожие инструкции для TMX428

Бренды по названию

Популярные бренды

Trackmaster TMX428, Руководство по обслуживанию

Результаты поиска

Содержание TMX428

Отзывы:

Похожие инструкции для TMX428

Бренды по названию

Популярные бренды