manualshive.com logo in svg

Trackmaster TMX428, Руководство по обслуживанию

Поделиться
Скачать
Trackmaster TMX428 Скачать руководство пользователя страница 43

TRACKMASTER 

Ch. 6 

Operating Instructions

 

 

317-160-406 Rev 4 

TMX428 TMX428CP & TMX58 Service Manual 

41 

 

May 2021 

 

 

Programmable Control Instructions TMX428CP 

The  TRACKMASTER

®

  TMX428CP  Programmable  Control  model  is  a  dual  purpose  treadmill 

capable  of  operating  for  cardiac  stress  testing  or  a  VO

2

  pulmonary  evaluation.  The  display 

automatically changes from a blue, full information screen (typically found on fitness treadmills), 
to  a  black  screen  under  controlled  thru  communication.  All  control  buttons  on  the  console  are 
disabled  in  this  mode  with  the  exception  of  the  two  stop  buttons  located  at  the  lower  left  and 
lower right of the control. The display will revert back to the full information screen upon closing 
the communications. 

TESTING MODE DISPLAY 

 
 

The  TRACKMASTER

®

TMX428CP  Control  model  is  a  full-featured,  stand-alone  fitness 

treadmill  suitable  for  rehabilitation  and  general  fitness  applications.  Additionally,  it  comes  pre-
programmed with 10 workouts, including Pre-Programmed Protocols and Interval Fitness training 
routines, in addition to 5 possible user defined workouts. 

MANUAL MODE DISPLAY 

 

 

 

 

Содержание TMX428
































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды